177-710-2-9CS8J1-24MCN datasheet, PDF

Datasheet> All Categories > The connector> The connector> 177-710-2-9CS8J1-24MCN

177-710-2-9CS8J1-24MCN: DescriptionInterconnection Device; CategoryThe connector The connector; File Size436KB，4 Pages; ManufacturerGlenair; Websitehttp://www.glenair.com/; Environmental Compliance

Download Datasheet Parametric View All

177-710-2-9CS8J1-24MCN Overview

Interconnection Device

177-710-2-9CS8J1-24MCN Parametric

Parameter Name	Attribute value
Is it lead-free?	Lead free
Is it Rohs certified?	conform to
Reach Compliance Code	compli
Connector type	INTERCONNECTION DEVICE
Base Number Matches	1

Preview

Download Datasheet

View All

MWDM Micro-D Shielded Cable Assemblies

Single-Ended or Double-Ended–These

easy-to-order cable

assemblies eliminate the need for expensive assembly

labor. 100% tested and ready for use.

Now With Twisted Pairs–No

need to create a procurement

speciﬁcation for Micro-D cables with twisted pairs. Glenair

177-740 cables are furnished with a full complement of

white/blue twisted pair wires.

Integral Shield Termination–The

connector shell has a

platform to accept Band-It shield termination bands. The

cable shield braid is attached directly to the connector.

Save Labor, Reduce Weight and Improve EMI Shielding with

Glenair’s Micro-D Shielded Cable Assemblies

Aerospace electronics systems require higher and higher levels of protection from radiated emissions. Glenair’s fully

shielded Micro-D cable assemblies meet this need. The cable shield is attached directly onto the one-piece connector

shell and secured with a stainless steel

BAND-IT

® clamp. These pre-wired, 100% tested assemblies meet the

requirements of MIL-DTL-83513. An optional ground spring on the pin connector assures low shell-to-shell resistance.

Available with a variety of wire types and shields, Micro-D shielded assemblies can be ordered in any length, either

single-ended or “back-to-back”.

Ground Spring and EMI Shielding Effectiveness

– A gold-plated

stainless steel ground spring on the pin connector mating face offers

substantial improvement in EMI protection. The graphs compare

identical connectors tested with and without ground springs.

EMI Performance with Ground Spring

SHIELDING EFFECTIVENESS (DB)

100

1.00E+03

100

1.00E+03

EMI Performance without Ground Spring

1.00E+04

1.00E+05

1.00E+06

1.00E+07

1.00E+08

1.00E+09

1.00E+04

1.00E+05

1.00E+06

1.00E+07

1.00E+08

1.00E+09

FREQUENCY (Hz)

CAGE Code 06324/0CA77

Printed in U.S.A.

GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912

www.glenair.com

B-8

E-Mail: sales@glenair.com

Recommended Resources

One of three signal switches, multi-way switch CD4027 multi-way switch

VFC100 synchronous voltage-frequency conversion circuit

Adjustable DC regulated power supply

Typical circuit of ICL7673 uninterruptible power supply

Zero-crossing detector circuit diagram C

25V precision regulated power supply circuit

SD card error, how to fix it?: Today I have an SD card, made into a U3 disk, which has been used normally. After a long time, it was found that the SD card was not formatted. I formatted it to FAT16 and the capacity was reduced by ...; chennature111 Embedded System

Design Considerations for Variable Speed Motor Drives Using Reverse Gate Drive Optocouplers: Design Considerations for Variable Speed Motor Drives Using Reverse Gate Drive Optocouplers...; 安_然 Analog electronics

Design of digital low-pass filter for harmonic detection: ...; eeleader FPGA/CPLD

AT91RM9200 SDRAM flash boot problem: Environment: AT91Rm9200 +S29Gl064A R6 SDRAM MT48LC16 U-boot +linux system Problem: After the board is booted from the internal rom, the uboot can be downloaded through commands and write data to the f...; sabergemini Embedded System

How to make the OS accept two HID devices with exactly the same VID and PID?: Project description: 1. Using chip HT82M99E 2. Purpose: simulate keyboard, upload small amount of data to PC. 3. All products have the same VID and PID. Problem description: 1. Assume there are two HI...; shamuwhale Embedded System

I have a small circuit. Can anyone help me analyze it?: Could you help me see what the function of Q1 is?...; 刘喜龙 Analog electronics

Shortcut: E0 E1 E2 E3 E4 E5 E6 E7 E8 E9 EA EB EC ED EE EF EG EH EI EJ EK EL EM EN EO EP EQ ER ES ET EU EV EW EX EY EZ F0 F1 F2 F3 F4 F5 F6 F7 F8 F9 FA FB FC FD FE FF FG FH FI FJ FK FL FM FN FO FP FQ FR FS FT FU FV FW FX FY FZ G0 G1 G2 G3 G4 G5 G6 G7 G8 G9 GA GB GC GD GE GF GG GH GI GJ GK GL GM GN GO GP GQ GR GS GT GU GV GW GX GZ H0 H1 H2 H3 H4 H5 H6 H7 H8 HA HB HC HD HE HF HG HH HI HJ HK HL HM HN HO HP HQ HR HS HT HU HV HW HX HY HZ I1 I2 I3 I4 I5 I6 I7 IA IB IC ID IE IF IG IH II IK IL IM IN IO IP IQ IR IS IT IU IV IW IX J0 J1 J2 J6 J7 JA JB JC JD JE JF JG JH JJ JK JL JM JN JP JQ JR JS JT JV JW JX JZ K0 K1 K2 K3 K4 K5 K6 K7 K8 K9 KA KB KC KD KE KF KG KH KI KJ KK KL KM KN KO KP KQ KR KS KT KU KV KW KX KY KZ

Popular Components