1.4 Deep sleep mode setting steps
The processor can enter sleep mode by calling the WFI instruction, but to enter deep sleep to achieve the lowest power consumption requires correct configuration. The...
[:|]The traffic light is controlled by an 8031 single-chip microcomputer, and the LED display is used to display the time. (1) The east-west and north-south directions are controlled alternately. 1) T...
Altera Quartus II Software DSE Demonstration Design Space Manager : https://training.eeworld.com.cn/course/2048Altera Quartus II Software DSE Demonstration Design Space Manager...
[i=s]This post was last edited by paulhyde on 2014-9-15 09:00[/i]Where can I find retail enameled wire, insulating paper and insulating varnish in Guangzhou?
I walked around all afternoon yesterday, b...
In MSP430F449, I want to store an integer number A in a place where it will not be lost when the power is off!As a parameter for the program to run later.Should it be placed in the FLASH? Or where is ...
Does anyone have the BSP of sirf atlasIII? Can you send me a copy? My QQ is 648433648, and my email address is sunboyljp@163.com. I would be very grateful!...
Chip: STM32F107VCT6 Application Pin: THOUSANDS, RMII STM32CubeMX is very convenient to use ETH. The software comes with LWIP and configuration. This time, STM32F107VCT6+DP83848CVV is used. The MII a...[Details]
After studying the F4 FSMC method to drive the touch screen for a few days, I have gained some understanding, which are listed below. The unorganized record is only for my own reference in the future...[Details]
At present, in the world,
the construction of
smart cities
is in the process of gradually landing from concept, and technology giants and investment giants are important participants in this...[Details]
This paper proposes a design scheme for an embedded CNC system based on ARM and FPGA. The software and hardware design of the ARM system, the implementation method of hardware fine interpolation ...[Details]
sprintf is a function in the C language library that converts data types. There is a situation where In 51 MCU, define unsigned char temp; Then I want to use the serial port to print out temp in deci...[Details]
In mid-to-late 2016, a girl from Hubei came to Beijing alone, full of curiosity about
cloud computing
. The girl left the deepest impression on me was her lovely smile. She told me that if ...[Details]
Introduction: As a power electronic device, the photovoltaic inverter mainly converts the direct current generated by the photovoltaic module into alternating current. Because there are thousands o...[Details]
Ouster LiDAR OS-1 (left) and OS-2 (center) Velodyne invented the modern 3D LiDAR scanner in the mid-2000s, but in recent years conventional wisdom has held that Velodyne’s design — 64 lasers mounted...[Details]
Today I am using the AD function of the stm8s microcontroller. There are ten channels from AN0 to AN9 on the microcontroller. I want to use only three of them, AN5 to AN7. //ADC initialization void A...[Details]
Table of contents: 1 Overview 2: Common interrupt functions 3: PWM output 1 Overview In development, timers are widely used, which can be simply summarized into three aspects: 1.1: Application of ...[Details]
6MHz crystal oscillator, using timer counter 1, using interrupt mode, through P1.0 to make a light emitting diode turn on for 100ms, turn off for 300ms, and repeat. Assembly programming is used to ac...[Details]
Try to design a subroutine, whose function is to rearrange the 6 single-byte positive integers in the internal RAM pointed to by (R0) in ascending order. ;========================================== ...[Details]
1. SCL is always controlled by the Master. SDA is controlled by the Slave when reading data and by the Master when writing data according to the direction of data transmission. After the 8-bit data i...[Details]
I read the description of I/O ports in the M16 manual, which says that you can use the internal pull-up resistor by setting DDXn=0, PORTn=1, PUD=0. Since this can be used, when using the key circuit,...[Details]