EEWORLDEEWORLDEEWORLD

Part Number

Search

51760-10305614BBLF

Description
Board Connector, Female, Right Angle, Press Fit Terminal, Guide Pin, Receptacle
CategoryThe connector    The connector   
File Size259KB,3 Pages
ManufacturerAmphenol
Websitehttp://www.amphenol.com/
Environmental Compliance
Download Datasheet Parametric View All

51760-10305614BBLF Overview

Board Connector, Female, Right Angle, Press Fit Terminal, Guide Pin, Receptacle

51760-10305614BBLF Parametric

Parameter NameAttribute value
Is it Rohs certified?conform to
Objectid307828282
Reach Compliance Codecompliant
ECCN codeEAR99
Board mount optionsHOLE .138-.163
body width0.47 inch
subject depth0.865 inch
body length6.3 inch
Body/casing typeRECEPTACLE
Connector typeBOARD CONNECTOR
Contact completed and terminatedTIN
Contact point genderFEMALE
Contact materialCOPPER ALLOY
Contact resistance20 mΩ
Contact styleHYBRID
Dielectric withstand voltage2500VDC V
Durability200 Cycles
maximum insertion force.973 N
Insulation resistance500000000 Ω
insulator materialGLASS FILLED POLYETHYLENE
Manufacturer's serial number51760
Mixed contactsYES
Installation option 1GUIDE PIN
Installation option 2LOCKING
Installation methodRIGHT ANGLE
Installation typeBOARD
Number of connectorsONE
Maximum operating temperature105 °C
Minimum operating temperature-55 °C
Rated current (signal)3 A
GuidelineUL
reliabilityCOMMERCIAL
Terminal length0.09 inch
Termination typePRESS FIT
Evacuation force-minimum value.17792 N
PDM: Rev:M
STATUS:
Released
Printed: Dec 20, 2010
.
[New version CH554]- ADC+PWM +Touch+HID ---Part 1
I got the board, so I'll just say a few words. I found out at the last minute that the chip can only be burned 200 times, and I don't have time to ask for more. Now I can only strictly "design first" ...
mig29ee MCU
It's hard for companies to block iPhones from accessing corporate networks
Andrew Jaquith said recently that it is difficult for enterprises to prevent iPhones from accessing the company network. Therefore, instead of resisting iPhones, it is better to be prepared to support...
liudong2008lldd RF/Wirelessly
Help: F2810 GPIO input problem
The pins CAP1_QEP1, CAP2_QEP2, and CAP3_QEPI1 of F2810 are used as GPIO signal input terminals. I set:GpioMuxRegs.GPAMUX.all = 0x00;GpioMuxRegs.GPADIR.all = 0xFF00;GpioMuxRegs.GPAQUAL.all = 0x0000;(1)...
kobe0601 Microcontroller MCU
How to use hardware circuit to filter out interference caused by signal jitter
[i=s]This post was last edited by jordanwys on 2014-7-3 09:40[/i] Due to the jitter of the motor (the resonance area of the stepper motor, it has been debugged for a long time, but it is still impossi...
jordanwys Analog electronics
How to set the lwip udp data receiving buffer size
I would like to ask how much data lwip UDP can receive at a time. I don't know which parameter controls the size of the received data. I can now receive 4KB of data, but if it is larger (such as 5K), ...
lidonglei1 stm32/stm8
SI9000 Impedance Calculation Instructions
...
qin552011373 ADI Reference Circuit

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 1921  2917  2416  92  2289  39  59  49  2  47 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号