177-710-2-100GP6K1-24BDG datasheet, PDF

Datasheet> All Categories > The connector> The connector> 177-710-2-100GP6K1-24BDG

177-710-2-100GP6K1-24BDG: DescriptionInterconnection Device; CategoryThe connector The connector; File Size436KB，4 Pages; ManufacturerGlenair; Websitehttp://www.glenair.com/

Download Datasheet Parametric View All

177-710-2-100GP6K1-24BDG Overview

Interconnection Device

177-710-2-100GP6K1-24BDG Parametric

Parameter Name	Attribute value
Is it lead-free?	Lead free
Reach Compliance Code	compli
Connector type	INTERCONNECTION DEVICE
Base Number Matches	1

Preview

Download Datasheet

View All

MWDM Micro-D Shielded Cable Assemblies

Single-Ended or Double-Ended–These

easy-to-order cable

assemblies eliminate the need for expensive assembly

labor. 100% tested and ready for use.

Now With Twisted Pairs–No

need to create a procurement

speciﬁcation for Micro-D cables with twisted pairs. Glenair

177-740 cables are furnished with a full complement of

white/blue twisted pair wires.

Integral Shield Termination–The

connector shell has a

platform to accept Band-It shield termination bands. The

cable shield braid is attached directly to the connector.

Save Labor, Reduce Weight and Improve EMI Shielding with

Glenair’s Micro-D Shielded Cable Assemblies

Aerospace electronics systems require higher and higher levels of protection from radiated emissions. Glenair’s fully

shielded Micro-D cable assemblies meet this need. The cable shield is attached directly onto the one-piece connector

shell and secured with a stainless steel

BAND-IT

® clamp. These pre-wired, 100% tested assemblies meet the

requirements of MIL-DTL-83513. An optional ground spring on the pin connector assures low shell-to-shell resistance.

Available with a variety of wire types and shields, Micro-D shielded assemblies can be ordered in any length, either

single-ended or “back-to-back”.

Ground Spring and EMI Shielding Effectiveness

– A gold-plated

stainless steel ground spring on the pin connector mating face offers

substantial improvement in EMI protection. The graphs compare

identical connectors tested with and without ground springs.

EMI Performance with Ground Spring

SHIELDING EFFECTIVENESS (DB)

100

1.00E+03

100

1.00E+03

EMI Performance without Ground Spring

1.00E+04

1.00E+05

1.00E+06

1.00E+07

1.00E+08

1.00E+09

1.00E+04

1.00E+05

1.00E+06

1.00E+07

1.00E+08

1.00E+09

FREQUENCY (Hz)

CAGE Code 06324/0CA77

Printed in U.S.A.

GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912

www.glenair.com

B-8

E-Mail: sales@glenair.com

Recommended Resources

Low frequency microphone circuit diagram

Gantry milling machine amplifier schematic circuit

Intercom power connector circuit diagram

555 infrared remote control eight-selection radio circuit

Inverter circuit 16

Thyristor circuit controlled by photocoupler

Design of 500WPFC power supply based on IC controller FAN4810: Design of 500WPFC power supply based on IC controller FAN4810 Abstract: The main features of the PFC controller FAN4810 are introduced, and the design procedure and method of a 500W high-performance P...; zbz0529 Power technology

The power supply outputs 5V stably when unloaded. After adding a 100 ohm resistor as a load, the output voltage is pulled down to 4.7V.: The power supply outputs 5V stably when unloaded. After adding a 100 ohm resistor as a load, the output voltage is pulled down to 4.7V. What is the problem? How should it be improved? Please give me s...; guzhaokaiaaaa Power technology

Simple electronic component tester: After the initial identification of RLC components or transistor three-terminal devices, the resistance, inductance, and capacitance values are converted into frequency values through the oscillation ...; 啸风916636 Renesas Electronics MCUs

Is Raspberry Pi considered open source hardware?: Raspberry Pi is well-known, but what makes people depressed is that the CPU BCM2837/BCM2835 used in this product is hard to buy on the market. So stop imitating! The only way is to buy Raspberry Pi pr...; bigbat DIY/Open Source Hardware

How to debug with ST-Link in Embedded Studio for ARM?: The ST routines provided by Segger are all debugged using J-Link. What if we only have an ST-Link emulator? In this article, we will introduce how to use ST-Link for debugging in Segger Embedded Studi...; MamoYU Real-time operating system RTOS

Altium Designer 14.1.5.iso Download: [i=s]This post was last edited by qinkaiabc on 2014-1-3 17:02[/i] Altium Designer 14.1.5.30772 [url=http://pan.baidu.com/s/1bnmYyZH]http://pan.baidu.com/s/1bnmYyZH[/url]Cracking method: [backcolor=rgb...; qinkaiabc PCB Design

Shortcut: A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 AA AB AC AD AE AF AG AH AI AJ AK AL AM AN AO AP AQ AR AS AT AU AV AW AX AY AZ B0 B1 B2 B3 B4 B5 B6 B7 B8 B9 BA BB BC BD BE BF BG BH BI BJ BK BL BM BN BO BP BQ BR BS BT BU BV BW BX BY BZ C0 C1 C2 C3 C4 C5 C6 C7 C8 C9 CA CB CC CD CE CF CG CH CI CJ CK CL CM CN CO CP CQ CR CS CT CU CV CW CX CY CZ D0 D1 D2 D3 D4 D5 D6 D7 D8 D9 DA DB DC DD DE DF DG DH DI DJ DK DL DM DN DO DP DQ DR DS DT DU DV DW DX DZ

Popular Components