EEWORLDEEWORLDEEWORLD

Part Number

Search

177-740-2-100GS4J1-18RNN

Description
Cable Assembly, 24AWG,
CategoryThe connector    Connector bracket   
File Size858KB,5 Pages
ManufacturerGlenair
Websitehttp://www.glenair.com/
Environmental Compliance
Download Datasheet Parametric View All

177-740-2-100GS4J1-18RNN Overview

Cable Assembly, 24AWG,

177-740-2-100GS4J1-18RNN Parametric

Parameter NameAttribute value
Is it Rohs certified?conform to
Objectid7005028832
Reach Compliance Codecompliant
Country Of OriginUSA
YTEOL8.23
Other featuresSTANDARD: MIL-DTL-83513
CertificationMIL
Conductor surface treatmentSILVER
conductor materialCOPPER
ConnectorSide1MICRO-D FEMALE
ConnectorSide2MICRO-D FEMALE
Connector bracket typeCABLE ASSEMBLY
structureSTRANDED
Cross-sectional area0.205 mm2
DIN complianceNO
IEC complianceNO
insulator materialCROSSLINKED ETHYLENE-TETRAFLUOROETHYLENE
length0.467 mm
MIL complianceYES
Number of conductors100
Maximum operating temperature150 °C
Minimum operating temperature-55 °C
Rated current3 A
Rated voltage150 V
resistance0.093 Ω
shieldNO
stay19X36
Wire gauge24 AWG
Wire and Cable NamesFLEXIBLE CORD AND FIXTURE WIRE
B
SHIELDING EFFECTIVENESS (Db)
1.00E+04
1.00E+05
1.00E+06
1.00E+07
1.00E+08
1.00E+09
SHIELDING EFFECTIVENESS (Db)
Micro-D Harness
EMI Performance with Ground Spring
100
90
80
70
60
50
40
30
20
10
0
1.00E+03
MWDM Micro-D
Shielded Cable Assembly
Single-Ended or Double-Ended–These
easy-to-order cable
assemblies eliminate the need for expensive assembly labor. 100%
tested and ready for use.
Now With Twisted Pairs–No
need to create a procurement
specification for Micro-D cables with twisted pairs. Glenair 177-740
cables are furnished with a full complement of white/blue twisted
pair wires.
Integral Shield Termination–The
connector shell has a platform
to accept Band-It shield termination bands. The cable shield braid is
attached directly to the connector.
Save Labor, Reduce Weight and Improve EMI Shielding
with Glenair’s Micro-D Shielded Cable Assemblies
Aerospace electronics systems require higher and higher levels of protection from radiated emissions. Glenair’s
fully shielded Micro-D cable assemblies meet this need. The cable shield is attached directly onto the one-
piece connector shell and secured with a stainless steel
Band-Master™ ATS
clamp. These pre-wired, 100% tested
assemblies meet the requirements of MIL-DTL-83513. An optional ground spring on the pin connector assures low
shell-to-shell resistance. Available with a variety of wire types and shields, Micro-D shielded assemblies can be
ordered in any length, either single-ended or “back-to-back”.
Ground Spring and EMI Shielding Effectiveness
A gold-plated stainless steel ground spring on the pin connector mating
face offers substantial improvement in EMI protection. The graphs
compare identical connectors tested with and without ground springs.
EMI Performance without Ground Spring
100
90
80
70
60
50
40
30
20
10
0
1.00E+03
1.00E+04
1.00E+05
1.00E+06
1.00E+07
1.00E+08
1.00E+09
frequency (Hz)
frequency (Hz)
© 2013 Glenair, Inc.
High Performance Micro-D Connectors and Cables
U.S. CAGE Code 06324
Printed in U.S.A.
GLENAIR, INC.
1211 AIR WAY
GLENDALE, CA 91201-2497
818-247-6000
FAX 818-500-9912
www.glenair.com
B-14
E-Mail: sales@glenair.com
EEWORLD University Hall--Introduction to LPCOpen software platform and its use
Introduction to LPCOpen software platform and its usage : https://training.eeworld.com.cn/course/597...
chenyy Embedded System
lm3s8962 driver codec chip plays mp3
Actually, I have already written an application... But a senior said that the file system and SD card read and write implementation are too wasteful for 8962... I would like to ask you a question, can...
xielijuan Microcontroller MCU
MSP430 driving 74HC595
Use MSP430 to drive 74HC595. Below is the main program. P2.0 is serial data input, P2.1 is RCK, and P2.2 is SCK. Assuming the serial input is 01010101, why can't I measure the voltage on the parallel ...
jinger0311 Microcontroller MCU
The internal crystal oscillator of STM32F103ZE cannot be used?
The ST3210E-LK development board is used for the test. The development environment is EWARM 5.0. There is no problem with the program started by the external crystal oscillator, but it cannot be used ...
babyspider stm32/stm8
Negative high voltage chip or solution
Hello everyone, due to recent demand, I need to use a chip with adjustable voltage output from -150V to -300V, and a few milliamperes of current. It would be best if it is an automotive-grade chip. Wh...
轩辕默殇 Power technology
Question: How to develop 16C554 driver on WinCE5.0 platform based on s3c2440?
Ask: How to develop 16C554 driver under WinCE5.0 platform of s3c2440? I have developed a simple 2x2 keyboard driver under WinCE. What reference materials should I use? Please recommend suitable books ...
archao Embedded System

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 94  1125  1895  2771  2448  2  23  39  56  50 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号