EEWORLDEEWORLDEEWORLD

Part Number

Search

GUB-GM8ALF-02-1522-D-B

Description
Array/Network Resistor, Isolated, Thin Film, 1.2W, 15200ohm, 0.5% +/-Tol, 50ppm/Cel, Surface Mount, 2244, DIP, ROHS COMPLIANT
CategoryPassive components    The resistor   
File Size493KB,3 Pages
ManufacturerTT Electronics plc
Websitehttp://www.ttelectronics.com/
Environmental Compliance  
Download Datasheet Parametric View All

GUB-GM8ALF-02-1522-D-B Overview

Array/Network Resistor, Isolated, Thin Film, 1.2W, 15200ohm, 0.5% +/-Tol, 50ppm/Cel, Surface Mount, 2244, DIP, ROHS COMPLIANT

GUB-GM8ALF-02-1522-D-B Parametric

Parameter NameAttribute value
Is it lead-free?Lead free
Is it Rohs certified?conform to
Objectid1076407400
package instructionSMT, 2244
Reach Compliance Codecompliant
Country Of OriginUSA
ECCN codeEAR99
YTEOL6.5
Other featuresULTRA PRECISION
structureMolded
Component power consumption0.16 W
The first element resistor15200 Ω
JESD-609 codee3
Manufacturer's serial numberGUB
Installation featuresSURFACE MOUNT
Network TypeISOLATED
Number of components1
Number of functions8
Number of terminals16
Maximum operating temperature125 °C
Minimum operating temperature-55 °C
Package height2.286 mm
Package length11.176 mm
Package shapeRECTANGULAR PACKAGE
Package formSMT
Package width5.588 mm
Rated power dissipation(P)1.2 W
Rated temperature70 °C
resistance15200 Ω
Resistor typeARRAY/NETWORK RESISTOR
seriesGUB
size code2244
surface mountYES
technologyTHIN FILM
Temperature Coefficient50 ppm/°C
Temperature coefficient tracking5 ppm/°C
Terminal surfaceMatte Tin (Sn)
Terminal shapeGULL WING
Tolerance0.5%
TaNFilm
®
Small Outline Surface
Mount Resistor Network
GUB Series
Thin film on ceramic technology
0.220” and 0.300” sizes available
RoHS compliant version available
DESC 87012 and 87013 available
Standard JEDEC packages for automatic placement equipment
Compliant leads to
compensate for
thermal expansion
and contractions.
IRC Advanced Film Division
Ultra precision tantalum
nitride resistance element
on high purity alumina.
Rugged, molded
construction.
IRC’s TaNFilm®, Small Outline Integrated Circuit resistor networks are ideally suited for surface mounting.
The 0.05 inch lead spacing provides higher lead density, increased component count, lower installed resistor
cost, and better reliability. They are ideally suited for the latest surface mount assembly techniques, and each
lead can be 100% visually inspected. The compliant leads relieve thermal expansion and contraction stressed
created by soldering and temperature excursions.
The tantalum nitride film system provides precision tolerance, exceptional TCR tracking, and low noise.
TaNFilm® provides stability, high reliability, and long life characteristics. Testing has demonstrated performance
exceeding MIL-PRF-83401 characteristics H.
Electrical Data
GM Type
Resistance Range (Ω)
GL Type
Absolute Tolerance
Ratio Tolerance To R1
TCR (ppm/°C)
TCR Tracking To R1 (ppm°C)
Operating Temperature Range
Noise
Substrate
Custom circuits and special testing available.
Schem A: 10 to 200K
Schem B: 10 to 1000K
Schem A: 10 to 150K
Schem B: 10 to 75K
Available to ±0.1%
Available to ±0.05%
±25, ±50, ±100
±5
-55°C to +125°C
Less than -25 dB
High purity alumina substrate
General Note
IRC reserves the right to make changes in product specification without notice or liability.
All information is subject to IRC’s own data and is considered accurate at time of going to print.
© IRC Advanced Film Division
• 4222 South Staples Street • Corpus Christi Texas 78411 USA
Telephone: 361 992 7900 • Facsimile: 361 992 3377 • Website: www.irctt.com
A subsidiary of
TT electronics plc
GUB Series Issue November 2008 Sheet 1 of 3
Some issues with "battery balancing"
[size=4] "Battery balancing" is not a new term. It has been used on nickel-cadmium batteries for at least 30 years. It's just that the early technology was simple and inefficient. Its principle and me...
qwqwqw2088 Analogue and Mixed Signal
How do you know if an 8-bit microcontroller is enough?
I made a pressure tester that needs to display 20000HPA. The unit must be HPA, and the output rate must not be less than 10KHZ....
qiangxiaochao MCU
Ask for help from high frequency wireless master
[i=s] This post was last edited by dontium on 2015-1-23 13:27 [/i] The frequency of the wireless transmitter module circuit is known to be 30MHZ. Now it needs to be changed to 10MHZ. How should it be ...
1017527621 Analogue and Mixed Signal
Small DC-DC boost power supply solution development requirements
[align=left][font=微软雅黑]Requirements for commissioned development of small DC-DC boost power supply solutions: [/font][/align][align=left][font=微软雅黑]1. Input voltage is 6-10Vdc. Maximum supply current ...
chdk11 Power technology
What is the problem with wireless?
What does it mean when using Protues to automatically lay out the first and then out? The simulation program is correct. Why does this happen?...
圈在指尖 PCB Design
MSP430 and SI446X
I want to ask everyone, has anyone done this before? What suggestions do you have for MSP430+SI446X? How much storage space and memory space is needed? Can the general 430 chip meet the requirements?...
newnew0601 Microcontroller MCU

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 1128  1869  2035  969  1606  23  38  41  20  33 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号