EEWORLDEEWORLDEEWORLD

Part Number

Search

8N3DV85AC-0113CDI8

Description
IC osc vcxo dual freq 6-clcc
Categorysemiconductor    Analog mixed-signal IC   
File Size169KB,20 Pages
ManufacturerIDT (Integrated Device Technology, Inc.)
Websitehttp://www.idt.com/
Environmental Compliance  
Download Datasheet Parametric View All

8N3DV85AC-0113CDI8 Online Shopping

Suppliers Part Number Price MOQ In stock  
8N3DV85AC-0113CDI8 - - View Buy Now

8N3DV85AC-0113CDI8 Overview

IC osc vcxo dual freq 6-clcc

8N3DV85AC-0113CDI8 Parametric

Parameter NameAttribute value
Datasheets
IDT8N3DV85
FemtoClock®
NG Ordering Guide
PCN Assembly/Origi
Passivation Thickness 12/Sep/2013
Standard Package1,000
CategoryIntegrated Circuits (ICs)
FamilyClock/Timing - Programmable Timers and Oscillators
PackagingTape & Reel (TR)
TypeVCXO
Cou-
Frequency156.25MHz, 175MHz
Voltage - Supply3.135 V ~ 3.465 V
Current - Supply130mA
Operating Temperature-40°C ~ 85°C
Package / Case6-CLCC
Supplier Device Package6-CLCC (7x5)
Mounting TypeSurface Mou
Other NamesIDT8N3DV85AC-0113CDI8IDT8N3DV85AC-0113CDI8-ND
LVPECL Dual-Frequency
Programmable VCXO
General Description
The IDT8N3DV85 is a LVPECL Dual-Frequency Programmable
VCXO with very flexible frequency and pull-range programming
capabilities. The device uses IDT’s fourth generation FemtoClock
®
NG technology for an optimum of high clock frequency and low
phase noise performance. The device accepts 2.5V or 3.3V supply
and is packaged in a small, lead-free (RoHS 6) 6-lead ceramic 5mm
x 7mm x 1.55mm package.
The device can be factory-programmed to any two frequencies in the
range of 15.476MHz to 866.67MHz and from 975MHz to 1,300MHz
to the very high degree of frequency precision of 218Hz or better.
The output frequency is selected by the FSEL pin. The extended
temperature range supports wireless infrastructure, telecommuni-
cation and networking end equipment requirements.
IDT8N3DV85
DATASHEET
Features
Fourth Generation FemtoClock
®
NG technology
Programmable clock output frequency from 15.476MHz to
866.67MHz and from 975MHz to 1,300MHz
Two factory-programmed output frequencies
VCO frequency programming resolution is 218Hz and better
Factory-programmable VCXO pull range and control voltage
polarity
VCXO pull range programmable from typical ±12.5 to ±787.5ppm
One 2.5V or 3.3V LVPECL clock output
FSEL control input for frequency selection, LVCMOS/LVTTL
compatible
RMS phase jitter @ 622.08MHz (12kHz - 20MHz):0.46ps (typical)
RMS phase jitter @ 622.08MHz (50kHz - 80MHz): 0.47ps (typical)
2.5V or 3.3V supply voltage
-40°C to 85°C ambient operating temperature
Lead-free (RoHS 6) 6-lead ceramic 5mm x 7mm x 1.55mm
package
Block Diagram
OSC
114.285 MHz
2
Pin Assignment
÷P
PFD
&
LPF
FemtoClock
®
NG
VCO
1950-2600MHz
VC
1
2
3
6
5
4
V
CC
nQ
Q
÷N
Q
nQ
FSEL
V
EE
÷MINT,
MFRAC
9
VC
Pulldown
A/D
23
Configuration Register (ROM)
(Frequency, Pull range, Polarity)
7
IDT8N3DV85
6-lead ceramic 5mm x 7mm x 1.55mm
package body
CD Package
Top View
FSEL
IDT8N3DV85CCD REVISION A OCTOBER 30, 2013
1
©2013 Integrated Device Technology, Inc.
Everyone recommends a shooter follower chip
Make a circuit to send the signal collected by the sensor to AD through a radio follower. I used op07 to form a radio follower, but my boss thought it was too slow, so I tried op27 but it didn't work....
megaf Analog electronics
Looking for a 50W chip that can work at 25-28GHz!
I'm looking for a 50W chip that can work at 25-28GHz! If anyone has one, please give me some reference suggestions, I'd be very grateful!...
ywtwd RF/Wirelessly
WINCE expansion TL15C255O
Hello everyone: I am now expanding TL16C2550 in WINCE. Now the bootloader reads LSR: uart+++ 14200000 B9E00000 0 test uart B9E00000 m_pData 0xB9E00000 m_pLCR 0xB9E00003 m_pData 0 lcr 0 m_pIER 0 m_pIIR...
ko1982 Embedded System
Detailed explanation of the solution to BOOT not working for NXP Cortex-M3 LPC1343 HEX generated BIN file in mass storage mode
Points: 211 Faction: Level: ------ From: Beijing Detailed explanation of NXP Cortex-M3 LPC1343 HEX generated BIN file for mass storage BOOT does not work: LPC1343 is indeed very convenient with its un...
huxiaoping NXP MCU
VMware (Hangzhou) Recruitment
Job Description: WinCE/WinMob RIL Driver Development Engineer 1. Master degree or above in computer or communication; 2. More than two years of embedded software development experience, proficient in ...
wanliinthesky Embedded System
Looking for a program to drive LCD12864O3 with MSP430. . .
I just bought an LCD12864 today, but the model may be different from the general one, so I can't drive it with the program of the expert on the Internet. I don't know how to connect the interface corr...
ccltilmvm Microcontroller MCU

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 523  2394  930  2231  2721  11  49  19  45  55 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号