EEWORLDEEWORLDEEWORLD

Part Number

Search

8N3DV85BC-0011CDI8

Description
IC osc vcxo dual freq 6-clcc
Categorysemiconductor    Analog mixed-signal IC   
File Size169KB,20 Pages
ManufacturerIDT (Integrated Device Technology, Inc.)
Websitehttp://www.idt.com/
Environmental Compliance  
Download Datasheet Parametric View All

8N3DV85BC-0011CDI8 Online Shopping

Suppliers Part Number Price MOQ In stock  
8N3DV85BC-0011CDI8 - - View Buy Now

8N3DV85BC-0011CDI8 Overview

IC osc vcxo dual freq 6-clcc

8N3DV85BC-0011CDI8 Parametric

Parameter NameAttribute value
Datasheets
IDT8N3DV85
FemtoClock®
NG Ordering Guide
PCN Assembly/Origi
Passivation Thickness 12/Sep/2013
Standard Package1,000
CategoryIntegrated Circuits (ICs)
FamilyClock/Timing - Programmable Timers and Oscillators
PackagingTape & Reel (TR)
TypeVCXO
Cou-
Frequency622.08MHz, 644.5313MHz
Voltage - Supply2.375 V ~ 2.625 V
Current - Supply120mA
Operating Temperature-40°C ~ 85°C
Package / Case6-CLCC
Supplier Device Package6-CLCC (7x5)
Mounting TypeSurface Mou
Other NamesIDT8N3DV85BC-0011CDI8IDT8N3DV85BC-0011CDI8-ND
LVPECL Dual-Frequency
Programmable VCXO
General Description
The IDT8N3DV85 is a LVPECL Dual-Frequency Programmable
VCXO with very flexible frequency and pull-range programming
capabilities. The device uses IDT’s fourth generation FemtoClock
®
NG technology for an optimum of high clock frequency and low
phase noise performance. The device accepts 2.5V or 3.3V supply
and is packaged in a small, lead-free (RoHS 6) 6-lead ceramic 5mm
x 7mm x 1.55mm package.
The device can be factory-programmed to any two frequencies in the
range of 15.476MHz to 866.67MHz and from 975MHz to 1,300MHz
to the very high degree of frequency precision of 218Hz or better.
The output frequency is selected by the FSEL pin. The extended
temperature range supports wireless infrastructure, telecommuni-
cation and networking end equipment requirements.
IDT8N3DV85
DATASHEET
Features
Fourth Generation FemtoClock
®
NG technology
Programmable clock output frequency from 15.476MHz to
866.67MHz and from 975MHz to 1,300MHz
Two factory-programmed output frequencies
VCO frequency programming resolution is 218Hz and better
Factory-programmable VCXO pull range and control voltage
polarity
VCXO pull range programmable from typical ±12.5 to ±787.5ppm
One 2.5V or 3.3V LVPECL clock output
FSEL control input for frequency selection, LVCMOS/LVTTL
compatible
RMS phase jitter @ 622.08MHz (12kHz - 20MHz):0.46ps (typical)
RMS phase jitter @ 622.08MHz (50kHz - 80MHz): 0.47ps (typical)
2.5V or 3.3V supply voltage
-40°C to 85°C ambient operating temperature
Lead-free (RoHS 6) 6-lead ceramic 5mm x 7mm x 1.55mm
package
Block Diagram
OSC
114.285 MHz
2
Pin Assignment
÷P
PFD
&
LPF
FemtoClock
®
NG
VCO
1950-2600MHz
VC
1
2
3
6
5
4
V
CC
nQ
Q
÷N
Q
nQ
FSEL
V
EE
÷MINT,
MFRAC
9
VC
Pulldown
A/D
23
Configuration Register (ROM)
(Frequency, Pull range, Polarity)
7
IDT8N3DV85
6-lead ceramic 5mm x 7mm x 1.55mm
package body
CD Package
Top View
FSEL
IDT8N3DV85CCD REVISION A OCTOBER 30, 2013
1
©2013 Integrated Device Technology, Inc.
A PPT about DSP/BIOS
...
firepower1 DSP and ARM Processors
TI Motor Control Solutions Brochure
TI provides a full range of motor drive and control solutions. It is a really good reference design document. In TI's motor control solution, different design solutions are given for different motors....
电容器 TI Technology Forum
I am about to graduate and I am a little confused about choosing a job. I would like to ask the seniors for some advice. Hehehe
I will graduate in the blink of an eye. When it comes to the real choice, I suddenly feel confused. I personally think I prefer hardware circuits. I don’t like pure software. I still like to tinker wi...
18811707971 Talking
Film resistors as resonant mode suppression layers in microwave circuit packaging
Typically, microwave circuits, especially MMICs, must be enclosed in metal packages to provide circuit protection and electrical isolation. However, this cavity may be designed to be large enough to s...
fighting PCB Design
When using 430f5529 to test 12864 display, %f cannot be displayed correctly
I directly used the project given to me by others to test whether 12864 can display successfully. As a result, on the same MCU, using the same program, after burning by others, the display screen can ...
多大点事er Microcontroller MCU
CCS5.1 Software Issues
During debugging, "Debugger Initialization Error" appears. Please help me....
mw102378 Microcontroller MCU

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 1603  1231  1286  455  2058  33  25  26  10  42 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号