EEWORLDEEWORLDEEWORLD

Part Number

Search

8N3DV85BC-0046CDI8

Description
IC osc vcxo dual freq 6-clcc
Categorysemiconductor    Analog mixed-signal IC   
File Size169KB,20 Pages
ManufacturerIDT (Integrated Device Technology, Inc.)
Websitehttp://www.idt.com/
Environmental Compliance  
Download Datasheet Parametric View All

8N3DV85BC-0046CDI8 Online Shopping

Suppliers Part Number Price MOQ In stock  
8N3DV85BC-0046CDI8 - - View Buy Now

8N3DV85BC-0046CDI8 Overview

IC osc vcxo dual freq 6-clcc

8N3DV85BC-0046CDI8 Parametric

Parameter NameAttribute value
Datasheets
IDT8N3DV85
FemtoClock®
NG Ordering Guide
PCN Assembly/Origi
Passivation Thickness 12/Sep/2013
Standard Package1,000
CategoryIntegrated Circuits (ICs)
FamilyClock/Timing - Programmable Timers and Oscillators
PackagingTape & Reel (TR)
TypeVCXO
Cou-
Frequency200MHz, 50MHz
Voltage - Supply2.375 V ~ 2.625 V
Current - Supply120mA
Operating Temperature-40°C ~ 85°C
Package / Case6-CLCC
Supplier Device Package6-CLCC (7x5)
Mounting TypeSurface Mou
Other NamesIDT8N3DV85BC-0046CDI8IDT8N3DV85BC-0046CDI8-ND
LVPECL Dual-Frequency
Programmable VCXO
General Description
The IDT8N3DV85 is a LVPECL Dual-Frequency Programmable
VCXO with very flexible frequency and pull-range programming
capabilities. The device uses IDT’s fourth generation FemtoClock
®
NG technology for an optimum of high clock frequency and low
phase noise performance. The device accepts 2.5V or 3.3V supply
and is packaged in a small, lead-free (RoHS 6) 6-lead ceramic 5mm
x 7mm x 1.55mm package.
The device can be factory-programmed to any two frequencies in the
range of 15.476MHz to 866.67MHz and from 975MHz to 1,300MHz
to the very high degree of frequency precision of 218Hz or better.
The output frequency is selected by the FSEL pin. The extended
temperature range supports wireless infrastructure, telecommuni-
cation and networking end equipment requirements.
IDT8N3DV85
DATASHEET
Features
Fourth Generation FemtoClock
®
NG technology
Programmable clock output frequency from 15.476MHz to
866.67MHz and from 975MHz to 1,300MHz
Two factory-programmed output frequencies
VCO frequency programming resolution is 218Hz and better
Factory-programmable VCXO pull range and control voltage
polarity
VCXO pull range programmable from typical ±12.5 to ±787.5ppm
One 2.5V or 3.3V LVPECL clock output
FSEL control input for frequency selection, LVCMOS/LVTTL
compatible
RMS phase jitter @ 622.08MHz (12kHz - 20MHz):0.46ps (typical)
RMS phase jitter @ 622.08MHz (50kHz - 80MHz): 0.47ps (typical)
2.5V or 3.3V supply voltage
-40°C to 85°C ambient operating temperature
Lead-free (RoHS 6) 6-lead ceramic 5mm x 7mm x 1.55mm
package
Block Diagram
OSC
114.285 MHz
2
Pin Assignment
÷P
PFD
&
LPF
FemtoClock
®
NG
VCO
1950-2600MHz
VC
1
2
3
6
5
4
V
CC
nQ
Q
÷N
Q
nQ
FSEL
V
EE
÷MINT,
MFRAC
9
VC
Pulldown
A/D
23
Configuration Register (ROM)
(Frequency, Pull range, Polarity)
7
IDT8N3DV85
6-lead ceramic 5mm x 7mm x 1.55mm
package body
CD Package
Top View
FSEL
IDT8N3DV85CCD REVISION A OCTOBER 30, 2013
1
©2013 Integrated Device Technology, Inc.
【Atmel SAM D21】Board first experience
It has been a while since I got the board. I have installed the corresponding software and ran a simple routine, but I have not posted it. Here are some photos of the board: Board packagingFront viewB...
啸风916636 MCU
Turning waste into treasure, Ameba runs MicroPython
[i=s] This post was last edited by strong161 on 2018-1-31 22:03 [/i] [size=4] I participated in a magical event two years ago and was given a set of smart pet house WeChat development board. "Smart Pe...
strong161 MicroPython Open Source section
A question about the use of ADS
When using ADS to compile NBOOT, for the same code, sometimes the compiler will shut down by itself and generate a FELF00NBOOT.BIN. Normally, it should be NBOOT.BIN. I wonder if anyone has encountered...
2008pcu Embedded System
Please tell me how to connect MMA7455 and 51 microcontroller
I need to use MMA7455 to measure angles. The microcontroller needs 51. 51 is 5V. 7455 is 3.3V. How to connect it without damage?...
w260743374 MCU
Home IoT access control part
The entire access control part is like using a 430 chip as a companion chip. The program flow on the 430 is as shown aboveSome program codes are in the attachmentFinally, let me share an example of TI...
zca123 DIY/Open Source Hardware
Questions about the ADC12 module
#include#include "BoardConfig.h" #define uint unsigned int #define uchar unsigned char uchar static adc_flag=0; uchar static count=0; void int_clk() { uchar i; BCSCTL1=~XT2OFF; BCSCTL2|SELM1+SELS; do ...
chen502 Microcontroller MCU

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 2446  671  2092  613  2557  50  14  43  13  52 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号