EEWORLDEEWORLDEEWORLD

Part Number

Search

D55342E07B210EMWI

Description
Fixed Resistor, Thin Film, 0.25W, 210000ohm, 100V, 1% +/-Tol, 25ppm/Cel, Surface Mount, 1206,
CategoryPassive components    The resistor   
File Size96KB,5 Pages
ManufacturerVishay
Websitehttp://www.vishay.com
Download Datasheet Parametric View All

D55342E07B210EMWI Overview

Fixed Resistor, Thin Film, 0.25W, 210000ohm, 100V, 1% +/-Tol, 25ppm/Cel, Surface Mount, 1206,

D55342E07B210EMWI Parametric

Parameter NameAttribute value
Is it Rohs certified?incompatible
Objectid7126377975
Reach Compliance Codenot_compliant
Country Of OriginUSA
ECCN codeEAR99
YTEOL7.85
Other featuresNON-INDUCTIVE
structureRectangular
JESD-609 codee0
Installation featuresSURFACE MOUNT
Number of terminals2
Maximum operating temperature150 °C
Minimum operating temperature-65 °C
Package height0.8382 mm
Package length3.2004 mm
Package formSMT
Package width1.6002 mm
method of packingWaffle Pack
Rated power dissipation(P)0.25 W
Rated temperature70 °C
GuidelineMIL-PRF-55342
resistance210000 Ω
Resistor typeFIXED RESISTOR
size code1206
surface mountYES
technologyTHIN FILM
Temperature Coefficient25 ppm/°C
Terminal surfaceTin/Lead (Sn90Pb10) - with Nickel (Ni) barrier
Terminal shapeWRAPAROUND
Tolerance1%
Operating Voltage100 V
E/H (Military M/D55342)
www.vishay.com
Vishay Dale Thin Film
QPL MIL-PRF-55342 Qualified
Thin Film Resistor, Surface-Mount Chip
FEATURES
• Established reliability, “S” and “V” failure rate level
(10 ppm), C = 2
• High purity alumina substrate
• Wraparound termination featuring a tenacious adhesion
layer covered with an electroplated nickel barrier layer for
+150 °C operating conditions
LINKS TO ADDITIONAL RESOURCES
• Very low noise and voltage coefficient
(< -25 dB, 0.5 ppm/V)
• Non-inductive
• Laser-trimmed tolerances ± 0.1 %
• Wraparound resistance less than 0.010
Ω
typical
• In-lot tracking less than 5 ppm/°C
• Complete MIL-testing available in-house
• Antistatic waffle pack or tape and reel packaging available
• Military / aerospace / QPL
D
D
3
3
3D Models
Thin Film Mil chip resistors feature all sputtered wraparound
termination for excellent adhesion and dimensional
uniformity. They are ideal in applications requiring stringent
performance requirements. Established reliability is assured
through 100 % screening and extensive environmental lot
testing.
CONSTRUCTION
Passivation
Resistor Film
Solder
Coating
Nickel Barrier
High Purity
Alumina Substrate
Adhesion Layer
TYPICAL PERFORMANCE
ABSOLUTE
TCR
TOL.
25
0.1
STANDARD ELECTRICAL SPECIFICATIONS
TEST
Material
Resistance Range
TCR: Absolute
Tolerance: Absolute
Stability: Absolute
Stability: Ratio
Voltage Coefficient
Working Voltage
Operating Temperature Range
Storage Temperature Range
Noise
Shelf Life Stability: Absolute
SPECIFICATIONS
Tamelox resistor film (passivated nichrome)
10
Ω
to 6.19 MΩ
± 25 ppm/°C to ± 300 ppm/°C
± 0.1 %, ± 0.25 %, ± 0.5 %, ± 1 %,
± 2 %, 5 %, ± 10 %
ΔR
± 0.02 %
-
0.1 ppm/V
30 V to 200 V
-65 °C to +150 °C
-65 °C to +150 °C
< - 25 dB
ΔR
± 0.01 %
CONDITIONS
-
-
-55 °C to +125 °C
+25 °C
2000 h at +70 °C
-
-
-
-
-
-
1 year at +25 °C
Revision: 15-Nov-2021
Document Number: 60018
1
For technical questions, contact:
thinfilm@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT
www.vishay.com/doc?91000
STM32L051's ADC conversion is inaccurate after wakeup
[font=宋体][size=5]After waking up from STM32L051 stop mode, the voltage converted by ADC is inaccurate. It needs to be initialized before each conversion. Has anyone encountered a similar situation? Pl...
943614033 stm32/stm8
STM32F429Discovery oscilloscope test heart rate
I was testing the pulse sensor at night and wondered if the STM32F429Discovery oscilloscope could be used to measure the waveform, so I tried it. Set the CH1 input, T=500ms, and adjust the offsetThe o...
dcexpert stm32/stm8
Question about bootloader interrupt vector
After reading the bootloader, I have some doubts: 1. When an exception occurs, the interrupt vector table is forced to jump by hardware according to the exception, and then the service program address...
taotaotalk Embedded System
Distribution analysis and maintenance of common faults in plc process control systems
In order to extend the life of the PLC control system, it is necessary to have a clear estimate of the equipment consumption and the failure points of the components and equipment in the system design...
frozenviolet Industrial Control Electronics
Discussing WINCE TCP/IP programming?
The PC version of TCP/IP has controls, but the WINCE version does not. It only has a SOCKET. Now some industrial control systems use TCP/IP, big data, real-time, and wireless. The serial port is also ...
tysym Embedded System
After installing the USB filter driver, how to solve the blue screen after restart?
Following the example in Chapter 22 of Zhang Fan's "Detailed Explanation of Windows Driver Development Technology", I made a USB filter driver and disabled the USB drive. After installing it and resta...
kunlun Embedded System

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 1582  2404  624  634  1763  32  49  13  36  12 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号