EEWORLDEEWORLDEEWORLD

Part Number

Search

8N4DV85FC-0120CDI

Description
IC osc vcxo dual freq 6-clcc
Categorysemiconductor    Analog mixed-signal IC   
File Size344KB,18 Pages
ManufacturerIDT (Integrated Device Technology, Inc.)
Websitehttp://www.idt.com/
Environmental Compliance  
Download Datasheet Parametric View All

8N4DV85FC-0120CDI Online Shopping

Suppliers Part Number Price MOQ In stock  
8N4DV85FC-0120CDI - - View Buy Now

8N4DV85FC-0120CDI Overview

IC osc vcxo dual freq 6-clcc

8N4DV85FC-0120CDI Parametric

Parameter NameAttribute value
Datasheets
IDT8N4DV85
FemtoClock®
NG Ordering Guide
PCN Assembly/Origi
Passivation Thickness 12/Sep/2013
Standard Package364
CategoryIntegrated Circuits (ICs)
FamilyClock/Timing - Programmable Timers and Oscillators
PackagingTray
TypeVCXO
Cou-
Frequency166.6667MHz, 166.6667MHz
Voltage - Supply2.375 V ~ 2.625 V
Current - Supply136mA
Operating Temperature-40°C ~ 85°C
Package / Case6-CLCC
Supplier Device Package6-CLCC (7x5)
Mounting TypeSurface Mou
Other NamesIDT8N4DV85FC-0120CDIIDT8N4DV85FC-0120CDI-ND
LVDS Dual-Frequency Programmable VCXO
IDT8N4DV85
DATASHEET
General Description
The IDT8N4DV85 is a LVDS Dual-Frequency Programmable VCXO
with very flexible frequency and pull-range programming capabilities.
The device uses IDT’s fourth generation FemtoClock® NG
technology for an optimum of high clock frequency and low phase
noise performance. The device accepts 2.5V or 3.3V supply and is
packaged in a small, lead-free (RoHS 6) 6-lead ceramic 5mm x 7mm
x 1.55mm package.
The device can be factory-programmed to any two frequencies in the
range of 15.476MHz to 866.67MHz and from 975MHz to 1300 MHz
to the very high degree of frequency precision of 218Hz or better.
The output frequency is selected by the FSEL pin. The extended
temperature range supports wireless infrastructure,
telecommunication and networking end equipment requirements.
Features
Fourth generation FemtoClock® NG technology
Programmable clock output frequency from 15.476MHz to
866.67MHz and from 975MHz to 1300MHz
Two factory-programmed output frequencies
Frequency programming resolution is 218Hz and better
Absolute pull range (APR) programmable from ±4.5 to ±754.5ppm
One 2.5V or 3.3V LVDS clock output
Output enable control input, LVCMOS/LVTTL compatible
RMS phase jitter @ 156.25MHz (12kHz - 20MHz): 0.47ps (typical)
2.5V or 3.3V supply voltage
-40°C to 85°C ambient operating temperature
Lead-free (RoHS 6) 6-lead ceramic 5mm x 7mm x 1.55mm
package
Block Diagram
OSC
114.285 MHz
2
Pin Assignment
÷P
PFD
&
LPF
FemtoClock® NG
VCO
1950-2600MHz
÷N
Q
nQ
VC 1
FSEL 2
GND 3
6 V
CC
5 nQ
4 Q
÷MINT,
MFRAC
9
IDT8N4DV85
6-lead ceramic 5mm x 7mm x 1.55mm
package body
CD Package
Top View
VC
Pulldown
A/D
23
Configuration Register (ROM)
(Frequency, Pull range, Polarity)
7
FSEL
IDT8N4DV85CCD REVISION B NOVEMBER 20, 2013
1
©2013 Integrated Device Technology, Inc.
51FPGA communication.. program can anyone help me annotate it, I don't understand it... follow the post
//MCU program: #include #include#include void outportb(unsigned char port, unsigned char nVal); unsigned char inportb(unsigned char port); unsigned char swap(unsigned char nVal); main() { while(1) { u...
ayuaini99 FPGA/CPLD
LPC1343 USB mass storage driver method to realize internal 32k flash read and write operations (routine analysis)
usbmsd_rom routine analysis: 1. Map the pointer to the on-chip driver table:ROM ** rom = (ROM **) 0x1fff1ff8; 2. Set device type and information: MscDevInfo.idVendor = USB_VENDOR_ID ;MscDevInfo.idProd...
gumuchixin NXP MCU
P1OUT = m<<1 | n<<3 | l<<4
void CTL74ls138(unsigned char m,unsigned char n,unsigned char l) { P1OUT = m<<1 | n<<3 | l<<4; } What does this program mean? The A, B, and C of 74LS138 are connected to P1.1, P1.3, and P1.4 of msp430...
wopuyao Microcontroller MCU
Show off my cc2650--TI Wireless Learning Carnival Season
[i=s]This post was last edited by youzizhile on 2016-7-1 20:38[/i] I received a call from FedEx today. I think it must be the cc2650 development board. I quickly retrieved the package, but found that ...
youzizhile Wireless Connectivity
HAL and normal assembly
Can HAL be used for embedded development?...
huanglinyu Embedded System
LPC1500 Experience + (3) Viewing LPCOpen source code using SourceInsight
[size=7]Use SourceInsight to view LPCOpen source code[size=3] Since LPCOpen routines are compiled libraries, it is very inconvenient to view the source code in Keil routines. You can only view it by a...
mars4zhu NXP MCU

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 1798  2430  2690  1059  317  37  49  55  22  7 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号