ABM2-07.000MHZ-33-D-7-T datasheet, PDF

Datasheet> All Categories > Passive components> Crystal/resonator> ABM2-07.000MHZ-33-D-7-T

ABM2-07.000MHZ-33-D-7-T: DescriptionParallel - Fundamental Quartz Crystal, 7MHz Nom, SMD, 2 PIN; CategoryPassive components Crystal/resonator; File Size686KB，2 Pages; ManufacturerAbracon; Websitehttp://www.abracon.com/index.htm

Download Datasheet Parametric View All

ABM2-07.000MHZ-33-D-7-T Overview

Parallel - Fundamental Quartz Crystal, 7MHz Nom, SMD, 2 PIN

ABM2-07.000MHZ-33-D-7-T Parametric

Parameter Name	Attribute value
Objectid	1841276405
package instruction	SMD, 2 PIN
Reach Compliance Code	compliant
Country Of Origin	Taiwan
YTEOL	6.9
Other features	AT-CUT; TR, 7 INCH
Ageing	5 PPM/YEAR
Crystal/Resonator Type	PARALLEL - FUNDAMENTAL
Drive level	10 µW
frequency stability	0.005%
frequency tolerance	15 ppm
JESD-609 code	e4
load capacitance	33 pF
Installation features	SURFACE MOUNT
Nominal operating frequency	7 MHz
Maximum operating temperature	85 °C
Minimum operating temperature	-40 °C
physical size	L8.0XB4.5XH1.4 (mm)/L0.315XB0.177XH0.055 (inch)
Series resistance	80 Ω
surface mount	YES
Terminal surface	Gold (Au) - with Nickel (Ni) barrier

Preview

Download Datasheet

View All

CERAMIC SMD MICROPROCESSOR CRYSTAL

ABM2

Pb in Glass

(exempt per RoHS 2002/95/EC Annex (5))

RoHS

Compliant

8.0 x 4.5 x 1.4mm

| | | | | | | | | | | | | | |

FEATURES:

• Glass sealed ceramic package assures high reliability.

• Ceramic package assures high reliability

• Tight tolerance and stability available

• IR reflow capable

APPLICATIONS:

• High density applications

• Modems, communication and test equipment

• PMCIA, Wireless applications

• Microprocessor crystals

STANDARD SPECIFICATIONS:

PARAMETERS

ABRACON P/N:

Frequency:

Operation Mode:

Operating Temperature:

Storage Temperature:

Frequency Tolerance:

Frequency Stability over the

Operating Temp. (Ref to +25°C):

Equivalent Series Resistance:

Shunt Capacitance C

Load Capacitance C

Drive Level:

Aging (per year) @ 25° C ± 3°C:

Insulation Resistance:

ABM2 Series

7.000 MHz to 60.000 MHz

7.00 MHz - 50.00 MHz

(Fundamental, AT-cut)

30.00 MHz - 60.00 MHz

(3rd Overtone, AT-cut)

- 10°C to + 60°C (see option)

- 40°C to + 90°C

± 50 ppm max. (see option)

See Table 1

5.0pF max.

Table 1

Frequency (MHz)

7.00-9.999 (Fund.)

10.00 - 15.999 (Fund.)

16.00 - 50.00(Fund.)

30.00 -60.00 (3rd O/T)

ESR(Ω) max.

18pF (see option)

100μW max., 10μW Typical

± 5ppm max.

(Left

100Vdc ± 15Vdc

500MΩ min. @

blank if standard)

OPTIONS AND PART IDENTIFICATION:

(Left blank if standard)

ABM2 - Frequency -

-R

Packaging

Tape and

Reel

F for Fundamental AT Cut

for F>=30MHz

Frequency

XX.XXX MHz

Load Capacitance

Please specify CL in pF or S

for Series (8 to 33 pF)

Operating Temp.

0°C to + 70°C

-20°C to +70°C

-30°C to +70°C

-30°C to +85°C

-40°C to +85°C

Freq. Tolerance

± 10 ppm

± 15 ppm

± 20 ppm

± 25 ppm

± 30 ppm

Standard operating temperature only.

Mode

RXXX (Value in

Ω

)

ESR

Freq. Stability

± 10 ppm*

± 12 ppm*

± 20 ppm*

± 25 ppm

± 30 ppm

± 35 ppm

ABRACON IS

ISO 9001 / QS 9000

CERTIFIED

Revised: 12.04.09

30332 Esperanza, Rancho Santa Margarita, California 92688

tel 949-546-8000

fax 949-546-8001

| www.abracon.com

Visit www.abracon.com for Terms & Conditions of Sale

Recommended Resources

LDB-1 type leakage protector circuit b

The simplest voice-controlled music lantern

Thyristor finishing circuit form circuit (5)

Interlock control circuit diagram of hydraulic motor of spindle motor on drilling machine

Light change detector drive relay circuit

Amplification circuit with gain controlled by logic instructions

【R7F0C809】LED+TIMER+UART+Key interrupt: After a whole afternoon of tinkering, I ran all the peripherals that might be used.Basically, they are GPIO, timers, serial ports, buttons, etc.I will also find examples to play with AD.1. LEDis very ...; ljj3166 Renesas Electronics MCUs

Photoelectric sensor circuit: [i=s] This post was last edited by elec32156 on 2017-11-3 10:04 [/i] As shown in the figure, it is the parameter specification of the light sensor. Different currents are output under different lighti...; elec32156 Power technology

On this side of the mountain and on the other side of the sea there is a group of programmers: [backcolor=rgb(238, 238, 238)][size=14px][font=Tahoma, Helvetica, SimSun, sans-serif][size=12px]I saw an article on the Internet, and excerpted an interesting passage: [/size][/font][/size][/backcolor...; 科技猎人 Talking

DWIN 86 box hardware development information sharing: There are two PCBs in the 86 box, one is the display board and the other is the peripheral control board. The two boards are connected by FCC10_1.0 cable, and the cable definition is: 5V PPWM2 PPWM1 P...; DWIN_IOT DIY/Open Source Hardware

Don't doubt it anymore! LED fluorescent lamps are great!: Let’s talk about the advantages and popularization trends of LED fluorescent lamps. 1. The production threshold of LED fluorescent tubes is relatively low. There are a wide variety of ready-made acces...; 探路者 LED Zone

430G2553 uses ACLK timer to output PWM which is unstable: I use ACLK as the timer clock source, in up-counting mode, to output PWM to control the LED brightness, but the actual output PWM is unstable, and the oscilloscope shows that the period and duty cycle...; 经世致用 Microcontroller MCU

Shortcut: E0 E1 E2 E3 E4 E5 E6 E7 E8 E9 EA EB EC ED EE EF EG EH EI EJ EK EL EM EN EO EP EQ ER ES ET EU EV EW EX EY EZ F0 F1 F2 F3 F4 F5 F6 F7 F8 F9 FA FB FC FD FE FF FG FH FI FJ FK FL FM FN FO FP FQ FR FS FT FU FV FW FX FY FZ G0 G1 G2 G3 G4 G5 G6 G7 G8 G9 GA GB GC GD GE GF GG GH GI GJ GK GL GM GN GO GP GQ GR GS GT GU GV GW GX GZ H0 H1 H2 H3 H4 H5 H6 H7 H8 HA HB HC HD HE HF HG HH HI HJ HK HL HM HN HO HP HQ HR HS HT HU HV HW HX HY HZ I1 I2 I3 I4 I5 I6 I7 IA IB IC ID IE IF IG IH II IK IL IM IN IO IP IQ IR IS IT IU IV IW IX J0 J1 J2 J6 J7 JA JB JC JD JE JF JG JH JJ JK JL JM JN JP JQ JR JS JT JV JW JX JZ K0 K1 K2 K3 K4 K5 K6 K7 K8 K9 KA KB KC KD KE KF KG KH KI KJ KK KL KM KN KO KP KQ KR KS KT KU KV KW KX KY KZ

Popular Components