EEWORLDEEWORLDEEWORLD

Part Number

Search

8N4SV76EC-0100CDI

Description
IC osc vcxo 100mhz 6-clcc
Categorysemiconductor    Analog mixed-signal IC   
File Size348KB,20 Pages
ManufacturerIDT (Integrated Device Technology, Inc.)
Websitehttp://www.idt.com/
Environmental Compliance  
Download Datasheet Parametric View All

8N4SV76EC-0100CDI Online Shopping

Suppliers Part Number Price MOQ In stock  
8N4SV76EC-0100CDI - - View Buy Now

8N4SV76EC-0100CDI Overview

IC osc vcxo 100mhz 6-clcc

8N4SV76EC-0100CDI Parametric

Parameter NameAttribute value
Datasheets
IDT8N4SV76
FemtoClock®
NG Ordering Guide
PCN Assembly/Origi
Passivation Thickness 12/Sep/2013
Standard Package364
CategoryIntegrated Circuits (ICs)
FamilyClock/Timing - Programmable Timers and Oscillators
PackagingTray
TypeVCXO
Cou-
Frequency100MHz
Voltage - Supply3.135 V ~ 3.465 V
Current - Supply140mA
Operating Temperature-40°C ~ 85°C
Package / Case6-CLCC
Supplier Device Package6-CLCC (7x5)
Mounting TypeSurface Mou
Other NamesIDT8N4SV76EC-0100CDIIDT8N4SV76EC-0100CDI-ND
LVDS Frequency-Programmable VCXO
IDT8N4SV76
DATASHEET
Factory Datasheet. Contains Confidential Information. Do not send to customers.
General Description
The IDT8N4SV76 is an LVDS Frequency-Programmable VCXO with
very flexible frequency and pull-range programming capabilities. The
device uses IDT’s fourth generation FemtoClock® NG technology for
an optimum of high clock frequency and low phase noise
performance. The device accepts 2.5V or 3.3V supply and is
packaged in a small, lead-free (RoHS 6) 6-lead ceramic 5mm x 7mm
x 1.55mm package.
The device can be factory-programmed to any frequency in the
range of 15.476MHz to 866.67MHz and from 975MHz to 1,300MHz
to the very high degree of frequency precision of 218Hz or better.
The extended temperature range supports wireless infrastructure,
telecommunication and networking end equipment requirements.
Features
Fourth generation FemtoClock® NG technology
Programmable clock output frequency from 15.476MHz to
866.67MHz and from 975MHz to 1,300MHz
Frequency programming resolution is 218Hz and better
Factory-programmable VCXO pull range and control voltage
polarity
Absolute pull-range (APR) programmable from ±4.5 to
±754.5ppm
One 2.5V or 3.3V LVDS clock output
Output enable control input, LVCMOS/LVTTL compatible
RMS phase jitter @ 156.25MHz (12kHz - 20MHz): 0.53ps (typical)
2.5V or 3.3V supply voltage
-40°C to 85°C ambient operating temperature
Lead-free (RoHS 6) 6-lead ceramic 5mm x 7mm x 1.55mm
package
Block Diagram
Pin Assignment
OSC
114.285 MHz
2
÷P
PFD
&
LPF
FemtoClock® NG
VCO
1950-2600MHz
÷N
Q
nQ
VC 1
nOE 2
GND 3
6 V
DD
5 nQ
4 Q
÷MINT,
MFRAC
7
IDT8N4SV76
6-lead ceramic 5mm x 7mm x 1.55mm
package body
CD Package
Top View
VC
A/D
25
Configuration Register (ROM)
(Frequency, Pull-range, Polarity)
7
nOE
Pulldown
Factory Datasheet. Contains Confidential Information. Do not send to customers.
IDT8N4SV76CCD REVISION B NOVEMBER 20, 2013
1
©2013 Integrated Device Technology, Inc.
The use of brake fluid in automobile anti-skid control system (Part 2)
(1) Open the reservoir cover and inject new brake fluid into the reservoir until the liquid level reaches the maximum liquid level mark (the "(2) If the brake system has just been repaired, or if the ...
frozenviolet Automotive Electronics
Output waveform distortion problem of improved differential circuit
The actual circuit is this, where r1=160k, r2=16M, c1 is 1nf, c2 is 1pf. The blue is the input test sine wave 5v Vpp 12hz, and the yellow output is distorted at this time. When the input is 11hz, ther...
fishiscat Analogue and Mixed Signal
Microbit Name Collection
Last week, I posted a thread to solicit opinions, and everyone gave a lot of good suggestions. However, many opinions are from a general direction, and few are specific, so I hope everyone can give so...
dcexpert MicroPython Open Source section
I would like to ask a question about external memory bus reading and writing
Connect the LCD controller to the 2407DSP in bus connection mode, that is,the LCD 8-bit data line DB7-DB0 is connected to the DSP data line D15-D18 pins,the LCD R/W is connected to the DSP address lin...
che3ccc Analogue and Mixed Signal
Ask about JFlash burning Atmel
Environment: JFlash SWD mode, three-wire SCLK SDIO GND Atmel SAMD10D14AM Problem 1, JFlash can connect to SAMD10, but the burning will probably fail. The error reported is “Can not read register 20 (C...
liudijiang Microchip MCU
New MicroPython Pi calculation performance comparison
Last weekend, I did a new comparison of pi calculations, comparing the performance of different processors by calculating pi with different digits. In addition to MicroPython, I also did a comparison ...
dcexpert MicroPython Open Source section

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 569  927  2138  655  1060  12  19  44  14  22 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号