7215SYABE datasheet, PDF - EEWORLD Datasheet

7215SYABE: DescriptionToggle Switch, DPDT, (on)-on-(on), Horizontal, 8 PCB Hole Cnt, Solder Terminal, Toggle Bat Actuator, Through Hole-right Angle; CategoryMechanical and electronic products switch; File Size188KB，2 Pages; ManufacturerITT; Websitehttp://www.ittcannon.com/

Download Datasheet Parametric View All

7215SYABE Online Shopping

Suppliers	Part Number	Price	MOQ	In stock
	7215SYABE	-	-	View	Buy Now

Toggle Switch, DPDT, (on)-on-(on), Horizontal, 8 PCB Hole Cnt, Solder Terminal, Toggle Bat Actuator, Through Hole-right Angle

Parameter Name	Attribute value
Objectid	1165992208
Reach Compliance Code	unknown
ECCN code	EAR99
Actuator angle	25 deg
Executor completed	BRIGHT CHROME
Actuator length	0.41 inch
Actuator material	BRASS
Actuator type	TOGGLE BAT
body width	11.43 mm
body height	36.449 mm
Body length or diameter	12.7 mm
Casing diameter	0.25 inch
Nozzle length	0.35 inch
Casing type	1/4-40
center contact material	COPPER ALLOY
Center contact plating	GOLD OVER NICKEL
Contact (DC) maximum rated power R load	0.4VA@20VDC
Contact function	(ON)-ON-(ON)
Contact resistance	0.01 mΩ
contact time	BREAK-BEFORE-MAKE
Dielectric withstand voltage	1000VRMS V
Electrical life	40000 Cycle(s)
End contact material	COPPER ALLOY
End contact plating	GOLD OVER NICKEL
Shell material	STAINLESS STEEL
Insulation resistance	1000000000 Ω
insulator material	GLASS FILLED NYLON
Manufacturer's serial number	7200
Installation features	THROUGH HOLE-RIGHT ANGLE
Maximum operating temperature	85 °C
Minimum operating temperature	-30 °C
PCB hole count	8
seal	EPOXY
Solderability	MIL-STD
surface mount	NO
Switch action	HORIZONTAL
switch function	DPDT
Switch type	TOGGLE SWITCH
Terminal surface	GOLD/NICKEL
Terminal length	0.125 inch
Terminal material	COPPER ALLOY
Termination type	SOLDER

PCB drawing board suggestions for B628 lithium battery boost circuit chip: B628 Boost IC Peripheral Components and PCB Design Practice PCB drawing board suggestions:As shown in the figure below, the red line from power input to output should be thick and wide. The inductor t...; kuake0618 LED Zone

RGMII interface clock delay setting?: In the registers of the PHY chip, you can set whether to add delay to the transmit and receive clocks, that is, RX Timing Delay mode and TX Timing Delay mode. When the rates are 1000Mbps and 10/100Mbp...; yuanjun1234 Integrated technical exchanges

Why is there a reverse rotation process when the inverter starts the motor?: Why is there a reverse rotation process when the inverter starts the motor? The motor used is a 6kw forward and reverse running brushless DC motor, and the inverter is 7.5kw from Shenzhen Sine Electri...; eeleader Industrial Control Electronics

Learning simulation + input bias current elimination resistor: [i=s] This post was last edited by dontium on 2015-1-23 11:46 [/i] The method of reducing bias error by introducing balancing resistors is taught by teachers in analog electronic technology class. But...; zca123 Analogue and Mixed Signal

Analysis of the causes of QuartusII simulation warning messages: When compiling and simulating in QuartusII, a lot of warnings will appear, some of which can be ignored, while others need attention. Although you can get help about the warning by pressing F1, someti...; phdwong FPGA/CPLD

Shortcut: E0 E1 E2 E3 E4 E5 E6 E7 E8 E9 EA EB EC ED EE EF EG EH EI EJ EK EL EM EN EO EP EQ ER ES ET EU EV EW EX EY EZ F0 F1 F2 F3 F4 F5 F6 F7 F8 F9 FA FB FC FD FE FF FG FH FI FJ FK FL FM FN FO FP FQ FR FS FT FU FV FW FX FY FZ G0 G1 G2 G3 G4 G5 G6 G7 G8 G9 GA GB GC GD GE GF GG GH GI GJ GK GL GM GN GO GP GQ GR GS GT GU GV GW GX GZ H0 H1 H2 H3 H4 H5 H6 H7 H8 HA HB HC HD HE HF HG HH HI HJ HK HL HM HN HO HP HQ HR HS HT HU HV HW HX HY HZ I1 I2 I3 I4 I5 I6 I7 IA IB IC ID IE IF IG IH II IK IL IM IN IO IP IQ IR IS IT IU IV IW IX J0 J1 J2 J6 J7 JA JB JC JD JE JF JG JH JJ JK JL JM JN JP JQ JR JS JT JV JW JX JZ K0 K1 K2 K3 K4 K5 K6 K7 K8 K9 KA KB KC KD KE KF KG KH KI KJ KK KL KM KN KO KP KQ KR KS KT KU KV KW KX KY KZ

Popular Components