SnPb end metallization option available upon request
(5% Pb minimum)
Applications
Typical applications include military, space quality and high reliability electronics.
Packaging C-Spec Ordering Options Table (100% Matte Sn and SnPb Terminations)
Packaging Type
1
Bulk Bag/Unmarked
7" Reel/Unmarked
13" Reel/Unmarked
7" Reel/Unmarked/2 mm pitch
2
13" Reel/Unmarked/2 mm pitch
2
1
1
Packaging/Grade
Ordering Code (C-Spec)
Not required (Blank)
TU
7411 (EIA 0603 and smaller case sizes)
7210 (EIA 0805 and larger case sizes)
7081
7082
Default packaging is “Bulk Bag”. An ordering code C-Spec is not required for “Bulk Bag” packaging.
The terms “Marked” and “Unmarked” pertain to laser marking option of capacitors. All packaging options labeled as “Unmarked” will contain
capacitors that have not been laser marked. The option to laser mark is not available on these devices. For more information see “Capacitor Marking”.
2
The 2 mm pitch option allows for double the packaging quantity of capacitors on a given reel size. This option is limited to EIA 0603 (1608 metric) case
size devices. For more information regarding 2 mm pitch option see “Tape & Reel Packaging Information”.
Default packaging is “Bulk Bag”. An ordering code C-Spec is not required for “Bulk Bag” packaging.
“Bulk Bag” packaging option is not available for Gold (Au) termination finish options and case sizes larger than 2225 (5664 Metric).
2
“Waffle Tray” packaging option is not available for case sizes larger than 2225 (5664 Metric).
3
The terms “Marked” and “Unmarked” pertain to laser marking option of components. All packaging options labeled as “Unmarked” will contain
capacitors that have not been laser marked. The option to laser mark is not available on these devices.
3
Reeling quantities are dependent upon chip size and thickness dimension. When ordering using the “T1K0” packaging option, 1812 through 2225 case
size devices with chip thickness of ≥ 1.9 mm (nominal) may be shipped on multiple 7” reels or a single 13” reel. Additional reeling or packaging options
may be available. Contact KEMET for details.
4
The 2 mm pitch option allows for double the packaging quantity of capacitors on a given reel size. This option is limited to EIA 0603 (1608 metric) case
size devices. For more information regarding 2 mm pitch option see “Tape & Reel Packaging Information”.
5
Additional reeling or packaging options may be available. Contact KEMET for details.
Capacitor Selection Tips in PCB ManufacturingSunday, 11/14/2010 - 14:54 — samqiuWhen there are contactors, relays, buttons and other components in the printed circuit board, they will generate large s...
[align=center][b][font=楷体, 楷体_GB2312][size=5][color=#ff00ff]Bare Metal Part 7 - ARM Working Mode & PSR Introduction & Stack Initialization[/color][/size][/font][/b][/align] [align=center][color=#ff00]...
LM3S3739 SSI initialization calls the peripheral library to set IO to SSI mode, then enters FaultISR? Software simulation is fine!
1.
// PA2 SSI0CLK(SSCK)GPIOPinTypeSSI(GPIO_PORTA_BASE, GPIO_PIN_2);
/...
Guangdong Traffic Regulation No. 355
To all municipal transportation bureaus (commissions) above the prefecture level, provincial transportation groups, Guangdong Power Grid Compa...[Details]
Recently, the Provincial Development and Reform Commission and the Provincial Poverty Alleviation Office jointly organized the application for a number of centralized photovoltaic poverty alleviation ...[Details]
0. Preparation First use st-link to connect the stm32 core board and PC for burning St-link Stm32 3.3V 3.3V GND GND SWDIO PART SWCLK DCLK Then connect with USB serial port board to v...[Details]
1. Determination of STM32 ADC sampling frequency 1. First, read some information to determine the ADC clock: (1) The ADCCLK clock provided by the clock controller is synchronized with the PCLK2 (A...[Details]
According to MEMS Consulting, Japan's
Toshiba
will further develop its automotive
LiDAR
(laser radar) semiconductor business, mainly focusing on: (1)
light receiving elements use...[Details]
At present, the Beidou system has achieved industrial breakthroughs and leapfrog development in five major areas, including the automotive OEM market, smart phones, and high-precision applications....[Details]
I am going to do a project recently, which requires counting the frequency and duty cycle of the external PWM signal. The chip used is STM32F207 Looking at the datasheet, I found that one of the ma...[Details]
The watchdog timer is used to prevent the program from running away due to strong interference noise caused by power supply, space electromagnetic interference or other reasons. Many microcontrollers...[Details]
Making a digital sampling oscilloscope has been my long-standing wish, but after all, this goal is quite difficult, and there are too many aspects involved, such as analog front-end circuit, high-spe...[Details]
At this exhibition, Microsoft brought its flagship intelligent voice products - XiaoIce and Xiaona. In addition, the voice will be equipped with an intelligent face recognition system. Let's see ho...[Details]
Use the STM32 timer input capture module to control 3-way ultrasonic sensors. The ultrasonic sensor used this time is the common HC-SR04, which is often used in the obstacle avoidance system of smal...[Details]
The STM8L contains a 12-bit ADC with 25 input channels, including an internal temperature sensor, an internal reference voltage As can be seen from the figure above, there is an internal re...[Details]
The key is the configuration of registers. The T1 timer (16 bits) of CC2530 needs to configure three registers: T1CTL, T1STAT, IRCON Here is just a brief introduction. For more details, please refer ...[Details]
MCS-51 single-chip microcomputer timer/counter experiment programming program Programming requirements: 1. Connect a light-emitting diode LED to the P1.0 pin, light up for two seconds, turn off for o...[Details]
Energy Infrastructure?
京公网安备 11010802033920号
EEWORLD
