INCH-POUND
MIL-C-11015/11F
14 May 2001
SUPERSEDING
MIL-C-11015/11E
10 July 1980
MILITARY SPECIFICATION SHEET
CAPACITORS, FIXED, CERAMIC DIELECTRIC (GENERAL PURPOSE),
STYLE CK62
This specification is approved for use by all Depart-
ments and Agencies of the Department of Defense.
The requirements for acquiring the product described herein
shall consist of this specification and MIL-C-11015.
INACTIVE FOR NEW DESIGN AFTER 31 MARCH 1999.
FOR REPLACEMENT PURPOSES ONLY.
NOTES:
1. Dimensions are in inches.
2. Metric equivalents are given for general information only.
3. Insulating coating shall not extend more than .125 (3.18 mm) along lead wires
measured from a tangent to the coating surface drawn perpendicular to the lead
wires.
FIGURE 1. Dimensions and configuration.
AMSC N/A
1 of 4
DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited.
Inches
.001
.004
.025
.040
.060
.120
.375
.550
1.250
mm
.03
.10
.64
1.02
1.52
3.05
9.53
13.97
31.75
FSC 5910
MIL-C-11015/11F
TABLE I. Style CK62 characteristics.
Rated
voltage
Volts, dc
1,500
1,500
1,500
1,500
1,500
500
500
500
500
500
500
500
Rated temperature
and voltage
temperature limits
AY
AY
AY
AY
AY
BX
BX
BX
AX
AW
AW
AW
Capacitance
Capacitance
tolerance
PIN
1/
CK62AY220M-
CK62AY470M-
CK62AY101M-
CK62AY221M-
CK62AY471M-
CK62BX821K-
CK62BX102--
CK62BX152--
CK62AX222--
CK62AW332M-
CK62AW472M-
CK62AW682M-
pF
22
47
100
220
470
820
1,000
1,500
2,200
3,300
4,700
6,800
M
M
M
M
M
K
K, M
K, M
K, M
M
M
M
1/ Where applicable, the complete PIN will include an additional symbol to indicate capacitance tolerance. The PIN
will also include the letter “E” to indicate an epoxy coated capacitor (when applicable) or “-“ will be deleted for wax
impregnated case.
REQUIREMENTS
Design and construction:
Dimensions and configuration - See figure 1.
Case type - Disk, wax impregnated or epoxy coated (E).
Capacitance value - See table I.
Capacitance tolerance -
10 percent (K) or
20 percent (M) as shown in table I.
Rated temperature - -55
C to +85
C (A) or -55
to +125
C (B) as shown in table I.
Dielectric withstanding voltage (DWV): In accordance with MIL-C-11015.
Dielectric:
Test voltage - 250 percent of rated voltage for voltage-temperature limits W and X, or 200 percent of rated
voltage for voltage-temperature limit Y.
Body insulation:
Test potential - 1,300 volts dc.
Barometric pressure (reduced): In accordance with MIL-C-11015 and method 105 of MIL-STD-202; condition B
(50,000 ft) for voltage-temperature limit AY, or 0.82 inch of mercury (80,000 ft) for voltage-temperature limits AW
and BX.
Test potential - 150 percent of rated voltage or 1,550 volts dc, whichever is less.
Insulation resistance (IR): In accordance with MIL-C-11015 and method 302 of MIL-STD-202, condition B.
200,000 megohms, minimum.
2
MIL-C-11015/11F
Dissipation factor (DF): 1.5 percent, maximum (voltage-temperature limit BX) or 2.0 percent, maximum (voltage-
temperature limits AW and AY).
Vibration, high frequency: In accordance with MIL-C-11015 and method 204 of MIL-STD-202, condition D (20 g’s).
Thermal shock and immersion: In accordance with MIL-C-11015.
DWV - 250 percent of rated voltage for voltage-temperature limits W and X, or 200 percent of rated voltage
for voltage-temperature limit Y.
IR - 150,000 megohms, minimum.
Salt spray (corrosion): Not applicable.
Terminal strength: In accordance with MIL-C-11015.
Moisture resistance: In accordance with MIL-C-11015.
DWV - 250 percent of rated voltage for voltage-temperature limits W and X, or 200 percent of rated voltage
for voltage-temperature limit Y.
IR - 150,000 megohms, minimum.
Cap. - Within tolerance of table I value.
Solderability: In accordance with MIL-C-11015. 2 terminals.
Resistance to soldering heat: In accordance with MIL-C-11015.
IR - 200,000 megohms, minimum.
Cap. -
5 percent of initial measurement.
DF - 0.5 percent, maximum.
Voltage-temperature limits: In accordance with MIL-C-11015.
Life (at elevated ambient temperature): In accordance with MIL-C-11015.
Test potential - 200 percent of rated voltage.
DWV - 250 percent of rated voltage for voltage-temperature limits AW and BX, or 200 percent of rated
voltage for voltage-temperature limit AY (at 25
C).
IR - 100,000 megohms, minimum (at high temperature and 25
C).
Cap. - Within tolerance of table I value (at 25
C).
DF - 1.5 percent, maximum (voltage-temperature limit BX) or 2.0 percent, maximum (voltage-temperature
limits AW and AY) (at 25
C).
Marking: In accordance with MIL-C-11015.
Changes from previous issue: Marginal notations are not used in this revision to identify changes with respect to
the previous issue due to the extent of the changes.
3
MIL-C-11015/11F
Custodians:
Army - CR
Navy - EC
Air Force - 11
DLA - CC
Review activities:
Army - MI
Navy – AS, OS, SH
Air Force - 19
Preparing activity:
DLA - CC
(Project 5910-2069-05)
4
京公网安备 11010802033920号
EEWORLD
