EEWORLDEEWORLDEEWORLD

Part Number

Search

M55342E06B1B21MT3

Description
RESISTOR, THIN FILM, 0.15 W, 0.1 %, 25 ppm, 1210 ohm, SURFACE MOUNT, 0705, CHIP, GREEN
CategoryPassive components    The resistor   
File Size96KB,5 Pages
ManufacturerVishay
Websitehttp://www.vishay.com
Download Datasheet Parametric View All

M55342E06B1B21MT3 Overview

RESISTOR, THIN FILM, 0.15 W, 0.1 %, 25 ppm, 1210 ohm, SURFACE MOUNT, 0705, CHIP, GREEN

M55342E06B1B21MT3 Parametric

Parameter NameAttribute value
Is it lead-free?Contains lead
Is it Rohs certified?incompatible
Objectid1761541968
package instructionSMT, 0705
Reach Compliance Codecompliant
Country Of OriginUSA
ECCN codeEAR99
YTEOL8
Other featuresNON-INDUCTIVE
structureRectangular
JESD-609 codee0
Installation featuresSURFACE MOUNT
Number of terminals2
Maximum operating temperature150 °C
Minimum operating temperature-65 °C
Package height0.8382 mm
Package length2.032 mm
Package shapeRECTANGULAR PACKAGE
Package formSMT
Package width1.27 mm
method of packingTR
Rated power dissipation(P)0.15 W
Rated temperature70 °C
GuidelineMIL-PRF-55342
resistance1210 Ω
Resistor typeFIXED RESISTOR
size code0705
surface mountYES
technologyTHIN FILM
Temperature Coefficient25 ppm/°C
Terminal surfaceTin/Lead (Sn60Pb40) - with Nickel (Ni) barrier
Terminal shapeWRAPAROUND
Tolerance0.1%
Operating Voltage50 V
E/H (Military M/D55342)
www.vishay.com
Vishay Dale Thin Film
QPL MIL-PRF-55342 Qualified
Thin Film Resistor, Surface-Mount Chip
FEATURES
• Established reliability, “S” and “V” failure rate level
(10 ppm), C = 2
• High purity alumina substrate
• Wraparound termination featuring a tenacious adhesion
layer covered with an electroplated nickel barrier layer for
+150 °C operating conditions
LINKS TO ADDITIONAL RESOURCES
• Very low noise and voltage coefficient
(< -25 dB, 0.5 ppm/V)
• Non-inductive
• Laser-trimmed tolerances ± 0.1 %
• Wraparound resistance less than 0.010
Ω
typical
• In-lot tracking less than 5 ppm/°C
• Complete MIL-testing available in-house
• Antistatic waffle pack or tape and reel packaging available
• Military / aerospace / QPL
D
D
3
3
3D Models
Thin Film Mil chip resistors feature all sputtered wraparound
termination for excellent adhesion and dimensional
uniformity. They are ideal in applications requiring stringent
performance requirements. Established reliability is assured
through 100 % screening and extensive environmental lot
testing.
CONSTRUCTION
Passivation
Resistor Film
Solder
Coating
Nickel Barrier
High Purity
Alumina Substrate
Adhesion Layer
TYPICAL PERFORMANCE
ABSOLUTE
TCR
TOL.
25
0.1
STANDARD ELECTRICAL SPECIFICATIONS
TEST
Material
Resistance Range
TCR: Absolute
Tolerance: Absolute
Stability: Absolute
Stability: Ratio
Voltage Coefficient
Working Voltage
Operating Temperature Range
Storage Temperature Range
Noise
Shelf Life Stability: Absolute
SPECIFICATIONS
Tamelox resistor film (passivated nichrome)
10
Ω
to 6.19 MΩ
± 25 ppm/°C to ± 300 ppm/°C
± 0.1 %, ± 0.25 %, ± 0.5 %, ± 1 %,
± 2 %, 5 %, ± 10 %
ΔR
± 0.02 %
-
0.1 ppm/V
30 V to 200 V
-65 °C to +150 °C
-65 °C to +150 °C
< - 25 dB
ΔR
± 0.01 %
CONDITIONS
-
-
-55 °C to +125 °C
+25 °C
2000 h at +70 °C
-
-
-
-
-
-
1 year at +25 °C
Revision: 15-Nov-2021
Document Number: 60018
1
For technical questions, contact:
thinfilm@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT
www.vishay.com/doc?91000
robot
About robot welding tracking...
yang371833340 Microcontroller MCU
Ask about the ground line of 485 communication
When the ground wire on the board is connected to the ground wire of JLINK, the 485 communication is normal.When it is not connected, the stm32 only receives but does not send signals.What is the reas...
langzileo stm32/stm8
Cruelfox Challenge Document Test Results
[i=s]This post was last edited by littleshrimp on 2018-2-4 14:59[/i] [font=微软雅黑][size=5]Yesterday I tested the hex file beacon_cruelfox_rev2.hex provided by @cruelfox[/size][/font][font=微软雅黑][size=5]T...
littleshrimp ST - Low Power RF
Practical settings for ISE to call modelsim for simulation
Practical settings for ISE to call modelsim for simulation. I installed ISE10.1 and ModelSim6.2b. ISE was installed first, and then ModelSim. I tried several methods before but couldn't connect. Final...
eeleader FPGA/CPLD
Chery's new car S21 is officially named QQ6 and will be launched soon
Recently, Chery Automobile Sales Company officially announced that the brand name of Chery's new car S21 is officially determined to be "QQ6", and it will be officially launched in China as early as A...
Narachu Automotive Electronics
DirectX/OpenGL Development
DirectX/OpenGL Development...
weipingid Embedded System

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 1716  2323  2540  2546  1579  35  47  52  32  20 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号