EEWORLDEEWORLDEEWORLD

Part Number

Search

ZW-21-19-F-Q-450-230

Description
Board Stacking Connector, 42 Contact(s), 2 Row(s), Male, Straight, Solder Terminal,
CategoryThe connector    The connector   
File Size242KB,1 Pages
ManufacturerSAMTEC
Websitehttp://www.samtec.com/
Environmental Compliance
Download Datasheet Parametric View All

ZW-21-19-F-Q-450-230 Overview

Board Stacking Connector, 42 Contact(s), 2 Row(s), Male, Straight, Solder Terminal,

ZW-21-19-F-Q-450-230 Parametric

Parameter NameAttribute value
Is it Rohs certified?conform to
Objectid2041300325
Reach Compliance Codecompliant
ECCN codeEAR99
YTEOL8.55
body width0.296 inch
subject depth0.45 inch
body length2.1 inch
Connector typeBOARD STACKING CONNECTOR
Contact to complete cooperationGOLD FLASH OVER NICKEL (50)
Contact completed and terminatedMatte Tin (Sn) - with Nickel (Ni) barrier
Contact point genderMALE
Contact materialPHOSPHOR BRONZE
contact modeRECTANGULAR
Contact styleSQ PIN-SKT
DIN complianceNO
Filter functionNO
IEC complianceNO
Insulator colorBLACK
insulator materialGLASS FILLED POLYESTER
JESD-609 codee3
MIL complianceNO
Plug contact pitch0.1 inch
Plug informationMULTIPLE MATING PARTS AVAILABLE
Mixed contactsNO
Installation methodSTRAIGHT
Installation typeBOARD
PCB row number2
Number of rows loaded2
OptionsGENERAL PURPOSE
Terminal pitch2.54 mm
Termination typeSOLDER
Total number of contacts42
Under 6410, I used IROM_Fusing_Tool.exe to make an SD card boot disk and burned something into it, but why did the SD card capacity not change? Is it hidden?
Under 6410, I used IROM_Fusing_Tool.exe to make an SD card boot disk and burned something into it, but why did the SD card capacity not change? Is it hidden?...
htjsmhj Embedded System
DFM should not be limited to chips, PCB needs it more
We all know that even if the silicon is 100% perfect, if any one component of the chip-to-chip communication link (such as the package, connector or circuit board) is damaged, the target system may st...
clj2004000 PCB Design
Report Forum
I've been busy making an amplifier recently, so I don't have time to share my experience with M3 with you. The information is not very valuable (I think the most valuable ones have been posted), and I...
heavenji Microcontroller MCU
Introduction to Intel Embedded Systems Invitational Competition
[i=s]This post was last edited by paulhyde on 2014-9-15 09:01[/i] The "Intel Cup Undergraduate Electronic Design Competition - Embedded System Special Invitational Competition" is part of the National...
open82977352 Electronics Design Contest
Adjustment of basic idle speed of electronically controlled vehicles 3
(2006-04-04 13:20:26 ) e. Turn off the engine after adjusting the basic idle speed, and then clear the fault code (35#) stored in the computer after disconnecting the ISCV circuit. Methods for clearin...
frozenviolet Automotive Electronics
What is the principle of transformer leakage inductance? Why do we need to short-circuit the secondary coil of the transformer when testing leakage inductance?
[size=4] When we use a bridge to test the leakage inductance of a transformer, we need to short-circuit the secondary side, and the inductance obtained by testing the primary side is the leakage induc...
qwqwqw2088 Analogue and Mixed Signal

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 2308  2432  2552  5  2513  47  49  52  1  51 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号