EEWORLDEEWORLDEEWORLD

Part Number

Search

B0202AS-03-5173-D

Description
Fixed Resistor, Thin Film, 0.25W, 517000ohm, 100V, 0.5% +/-Tol, 25ppm/Cel, Surface Mount, 0202, CHIP
CategoryPassive components    The resistor   
File Size381KB,3 Pages
ManufacturerTT Electronics plc
Websitehttp://www.ttelectronics.com/
Download Datasheet Parametric View All

B0202AS-03-5173-D Overview

Fixed Resistor, Thin Film, 0.25W, 517000ohm, 100V, 0.5% +/-Tol, 25ppm/Cel, Surface Mount, 0202, CHIP

B0202AS-03-5173-D Parametric

Parameter NameAttribute value
Objectid1579378241
package instructionCHIP
Reach Compliance Codecompliant
ECCN codeEAR99
Installation featuresSURFACE MOUNT
Number of terminals2
Maximum operating temperature150 °C
Minimum operating temperature-55 °C
Package shapeRECTANGULAR PACKAGE
method of packingTRAY
Rated power dissipation(P)0.25 W
Rated temperature70 °C
resistance517000 Ω
Resistor typeFIXED RESISTOR
size code0202
surface mountYES
technologyTHIN FILM
Temperature Coefficient25 ppm/°C
Terminal shapeONE SURFACE
Tolerance0.5%
Operating Voltage100 V
Wire Bondable
Chip Resistors
WBC Series
Discrete or tapped schematics
MIL inspection available
High resistor density
IRC’s WBC series wire bondable chip resistors are ideally suited for
the most demanding hybrid application. The WBC combines IRC’s
TaNSil
®
tantalum nitride thin film technology with silicon substrate processing to produce an extremely small
footprint device with the proven stability, reliability and moisture performance of IRC’s TaNSil
®
resistor film.
Available in a wide range of tolerances and temperature coefficients to fit a variety of hybrid circuit applica-
tions. Custom resistance values, sizes and schematics are available on request from the factory.
Physical Data
R0202 - Discrete
(0.508mm ±0.025)
0.020˝ ±0.001
Electrical Data
Absolute Tolerance
Absolute TCR
Package Power Rating
(@ 70°C)
Rated Operating Voltage
(not to exceed P x R )
Operating Temperature
Back contact
Noise
R
Top contact
pad chamfered
0.004˝ min bond pad size
to ±0.1%
to ±25ppm/°C
250mW
100V
-55°C to +150°C
<-30dB
Oxidized Silicon
(10KÅ SiO
2
min)
0.010˝ ±0.001
(0.254mm ±0.025)
10KÅ minimum
15KÅ minimum
Silicon
(Al / Au optional)
3KÅ Au minimum
10KÅ Al minimum
Silicon Dioxide or
Silicon Nitride
R
0.004˝ min bond pad size
0.020˝ ±0.001
(0.508mm ±0.025)
B0202 - Discrete back contact
(0.508mm ±0.025)
0.020˝ ±0.001
Substrate Material
Top contact
Substrate Thickness
Aluminum
Gold
R0202 and
T0303
B0202
0.020˝ ±0.001
(0.508mm ±0.025)
T0303 - Tapped network ½R + ½R
Bond Pad
Metallization
(0.762mm ±0.025)
0.030˝ ±0.001
½R
½R
Backside
0.030˝ ±0.001
(0.762mm ±0.025)
0.004˝ min bond pad size
Passivation
General Note
IRC reserves the right to make changes in product specification without notice or liability.
All information is subject to IRC’s own data and is considered accurate at time of going to print.
© IRC Advanced Film Division
• Corpus Christi Texas 78411 USA
Telephone: 361 992 7900 • Facsimile: 361 992 3377 • Website: www.irctt.com
A subsidiary of
TT electronics plc
WBC Series Issue January 2009 Sheet 1 of 3
About the status of the pull-up and pull-down resistors inside the MSP430
When the MSP430 microcontroller IO port is used to detect high and low levels, no external pull-up or pull-down is required because it has internal pull-up and pull-down.When used as high or low level...
exiao Microcontroller MCU
How NEC's chips drive DC motors
[i=s]This post was last edited by paulhyde on 2014-9-15 09:27[/i] The control mode of the chip driving the stepper motor is more flexible, but for driving the DC motor, the only thing that can be chan...
sabermail Electronics Design Contest
Emergency lighting solution
[[i]This post was last edited by jxb01033016 on 2010-8-18 09:38[/i]]...
jxb01033016 DIY/Open Source Hardware
Channel Estimation & Equalization for WiMAX
Introduction The Altera channel estimation and equalization modules for mobile worldwide interoperability for microwave access (WiMAX) can be used to accelerate the development of mobile broadband wir...
xiaoxin1 FPGA/CPLD
boot settings
My chip is STM32F103c6t6a. How do I set boot0=1 boot1=0? I use STMISP to burnThe instructions for this software are to set boot0=1 boot1=0 first. How do I set it? Thank you [[i ] This post was last ed...
hsiuen stm32/stm8
Win a JD.com card! Check in at Infineon's new SiC MOSFET pop-up store
Event time: From now until July 24Event process:1. Click the "Check-in now" button below to enter the pop-up store and start the event;2. Click on the 4 check-in points in the pop-up store, follow the...
EEWORLD社区 Power technology

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 212  1051  558  1641  993  5  22  12  34  20 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号