EEWORLDEEWORLDEEWORLD

Part Number

Search

B0202GA-03-4421-B

Description
Fixed Resistor, Thin Film, 0.25W, 4420ohm, 100V, 0.1% +/-Tol, 25ppm/Cel, Surface Mount, 0202, CHIP
CategoryPassive components    The resistor   
File Size381KB,3 Pages
ManufacturerTT Electronics plc
Websitehttp://www.ttelectronics.com/
Download Datasheet Parametric View All

B0202GA-03-4421-B Overview

Fixed Resistor, Thin Film, 0.25W, 4420ohm, 100V, 0.1% +/-Tol, 25ppm/Cel, Surface Mount, 0202, CHIP

B0202GA-03-4421-B Parametric

Parameter NameAttribute value
Objectid1579390635
package instruction, 0202
Reach Compliance Codecompliant
ECCN codeEAR99
Installation featuresSURFACE MOUNT
Number of terminals2
Maximum operating temperature150 °C
Minimum operating temperature-55 °C
Package shapeRECTANGULAR PACKAGE
method of packingTRAY
Rated power dissipation(P)0.25 W
Rated temperature70 °C
resistance4420 Ω
Resistor typeFIXED RESISTOR
size code0202
surface mountYES
technologyTHIN FILM
Temperature Coefficient25 ppm/°C
Terminal shapeONE SURFACE
Tolerance0.1%
Operating Voltage100 V
Wire Bondable
Chip Resistors
WBC Series
Discrete or tapped schematics
MIL inspection available
High resistor density
IRC’s WBC series wire bondable chip resistors are ideally suited for
the most demanding hybrid application. The WBC combines IRC’s
TaNSil
®
tantalum nitride thin film technology with silicon substrate processing to produce an extremely small
footprint device with the proven stability, reliability and moisture performance of IRC’s TaNSil
®
resistor film.
Available in a wide range of tolerances and temperature coefficients to fit a variety of hybrid circuit applica-
tions. Custom resistance values, sizes and schematics are available on request from the factory.
Physical Data
R0202 - Discrete
(0.508mm ±0.025)
0.020˝ ±0.001
Electrical Data
Absolute Tolerance
Absolute TCR
Package Power Rating
(@ 70°C)
Rated Operating Voltage
(not to exceed P x R )
Operating Temperature
Back contact
Noise
R
Top contact
pad chamfered
0.004˝ min bond pad size
to ±0.1%
to ±25ppm/°C
250mW
100V
-55°C to +150°C
<-30dB
Oxidized Silicon
(10KÅ SiO
2
min)
0.010˝ ±0.001
(0.254mm ±0.025)
10KÅ minimum
15KÅ minimum
Silicon
(Al / Au optional)
3KÅ Au minimum
10KÅ Al minimum
Silicon Dioxide or
Silicon Nitride
R
0.004˝ min bond pad size
0.020˝ ±0.001
(0.508mm ±0.025)
B0202 - Discrete back contact
(0.508mm ±0.025)
0.020˝ ±0.001
Substrate Material
Top contact
Substrate Thickness
Aluminum
Gold
R0202 and
T0303
B0202
0.020˝ ±0.001
(0.508mm ±0.025)
T0303 - Tapped network ½R + ½R
Bond Pad
Metallization
(0.762mm ±0.025)
0.030˝ ±0.001
½R
½R
Backside
0.030˝ ±0.001
(0.762mm ±0.025)
0.004˝ min bond pad size
Passivation
General Note
IRC reserves the right to make changes in product specification without notice or liability.
All information is subject to IRC’s own data and is considered accurate at time of going to print.
© IRC Advanced Film Division
• Corpus Christi Texas 78411 USA
Telephone: 361 992 7900 • Facsimile: 361 992 3377 • Website: www.irctt.com
A subsidiary of
TT electronics plc
WBC Series Issue January 2009 Sheet 1 of 3
Power failure occurs when the PMOS tube controls the power switch
In the figure, blue is the gate voltage and yellow is VBAT. Figure 1 shows the TPS61220 boost chip enable pin pulled high according to the schematic diagram. Figure 2 shows the TPS61220 boost chip ena...
xieyj Power technology
Development of TI LM3S8962 based on LabVIEW graphical interface--Step 3 (1)
Development of TI LM3S8962 based on LabVIEW graphical interface--Step 3: Preliminary development and debugging of LM3S8962: Part 1After step zero, step one, and step two, we have completed all the pre...
wanghongyang Microcontroller MCU
msp430 launchpad watchdog timer operation
Set the msp430 watchdog timer to interrupt once every 32ms to make the LED flash. #includevoid main(void){WDTCTL = WDT_MDLY_32;// Set Watchdog Timer interval to ~30ms(WDTPW+WDTTMSEL+WDTCNTCL)IE1 |= WD...
wateras1 Microcontroller MCU
Characteristics and selection of common protection components for lightning overvoltage protection
There are three main methods for lightning protection: 1. Avoidance: Correctly select the route and site (equipment placement point) of the line, and consciously try to avoid the lightning strike area...
langtuodianzi Integrated technical exchanges
How should we build our section? We welcome your suggestions!
I have been a moderator for a while, and I have some ideas and insights of my own! Let me talk about some of my own immature ideas! First of all, for those who do nothing but post the topic of course ...
小小白 51mcu
Midea induction cooker circuit and maintenance
[color=#800080]M02-B2 board has intermittent heating after power on.[/color]...
aimyself DIY/Open Source Hardware

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 2732  2401  945  373  1688  56  49  20  8  34 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号