DIP1989033001JB datasheet, PDF

Datasheet> All Categories > Passive components> The resistor> DIP1989033001JB

DIP1989033001JB: DescriptionArray/Network Resistor, Isolated, 0.2W, 3000ohm, 100V, 5% +/-Tol, -25,25ppm/Cel, 7025,; CategoryPassive components The resistor; File Size334KB，3 Pages; ManufacturerTT Electronics plc; Websitehttp://www.ttelectronics.com/; Environmental Compliance

Download Datasheet Parametric View All

DIP1989033001JB Overview

Array/Network Resistor, Isolated, 0.2W, 3000ohm, 100V, 5% +/-Tol, -25,25ppm/Cel, 7025,

DIP1989033001JB Parametric

Parameter Name	Attribute value
Is it Rohs certified?	conform to
Objectid	791706300
Reach Compliance Code	compliant
Country Of Origin	USA
ECCN code	EAR99
YTEOL	6.9
structure	Welded
JESD-609 code	e4
Lead length	3.429 mm
lead spacing	2.54 mm
Network Type	Isolated
Number of terminals	14
Maximum operating temperature	150 °C
Minimum operating temperature	-55 °C
Package height	2.032 mm
Package length	17.78 mm
Package form	DIP
Package width	6.35 mm
Rated power dissipation(P)	0.2 W
resistance	3000 Ω
Resistor type	ARRAY/NETWORK RESISTOR
series	1900
size code	7025
Temperature Coefficient	25 ppm/°C
Terminal surface	Gold (Au)
Tolerance	5%
Operating Voltage	100 V

DIP1989033001JB Preview

TaNFilm Precision DIP Network

Commercial and MIL Qualified

1900 Series

Inherent reliability

MIL-PRF-83401 qualified

Custom configuration available

Bonded leads not susceptible to

solder reflow problems

Absolute tolerance to

±0.1% / ratio tolerance to ±0.05%

Absolute TCR to

±15ppm/°C / ratio tracking to ±5ppm/°C



√

_____

General Note

TT electronics reserves the right to make changes in product specification without notice or liability.

All information is subject to TT electronics’ own data and is considered accurate at time of going to print.

www.bitechnologies.com www.irctt.com www.welwyn-tt.com

09. 11

TaNFilm

Precision DIP Network

Commercial and MIL Qualified

1900 Series

General Note

TT electronics reserves the right to make changes in product specification without notice or liability.

All information is subject to TT electronics’ own data and is considered accurate at time of going to print.

www.bitechnologies.com www.irctt.com www.welwyn-tt.com

09. 11

TaNFilm

Precision DIP Network

Commercial and MIL Qualified

1900 Series

General Note

TT electronics reserves the right to make changes in product specification without notice or liability.

All information is subject to TT electronics’ own data and is considered accurate at time of going to print.

www.bitechnologies.com www.irctt.com www.welwyn-tt.com

09. 11

More (Only the first 5 pages are displayed. Please Download Datasheet to view the full content.) >

Recommended Resources

Touch delay light switch circuit (4)

FM (frequency modulation) signal demodulator circuit diagram A

Pierce crystal oscillator

Universal frequency converter regulates the speed of single-phase motors

Intelligent "Big Brother" battery charger circuit

Calculator used as counting circuit

Please advise on the issue of porting C++ software to VxWorks under Linux: A C++ framework under Linux, consisting of many folders and makefiles. The main question is what changes should be made to the gnu makefile under Linux in order to compile a program that can run under...; xmmant Linux and Android

Asking for advice: smclk of msp430afe253: Has anyone used the msp430afe253 microcontroller? When I used this microcontroller, I measured the output of smclk and it was always high. I used the routine provided by TI and it was still high. Has ...; 绵里针 Microcontroller MCU

Microcontroller Application Programming (Book): Microcontroller Application Programming Design (Book), Super Star Reading Format http://www.dykf.com/Soft/ShowSoftDown.asp?UrlID=1SoftID=104...; fighting MCU

High speed ADC chip, who has any recommendations?: I saw a CS5510/11/12/13 in Cirrus Logic, but the PDF says that an external op amp is required. I don't want to add any extra external circuits. Has anyone done a similar project? The AD output rate ne...; slevin Embedded System

Help, multisim simulation always fails: I want to use multisim10.0 to simulate a circuit related to a potentiometer. However, when the potentiometer is set to 100%, the error shown in the picture will appear. I really don't know where the p...; sizumiyazhao Integrated technical exchanges

Why does this prompt appear when burning code with Keil?: Target dll has been canceled Debugger aborted...; zldzjzldh Embedded System

Shortcut: S0 S1 S2 S3 S4 S5 S6 S7 S8 S9 SA SB SC SD SE SF SG SH SI SJ SK SL SM SN SO SP SQ SR SS ST SU SV SW SX SY SZ T0 T1 T2 T3 T4 T5 T6 T7 T8 T9 TA TB TC TD TE TF TG TH TI TJ TK TL TM TN TO TP TQ TR TS TT TU TV TW TX TY TZ U0 U1 U2 U3 U4 U6 U7 U8 UA UB UC UD UE UF UG UH UI UJ UK UL UM UN UP UQ UR US UT UU UV UW UX UZ V0 V1 V2 V3 V4 V5 V6 V7 V8 V9 VA VB VC VD VE VF VG VH VI VJ VK VL VM VN VO VP VQ VR VS VT VU VV VW VX VY VZ W0 W1 W2 W3 W4 W5 W6 W7 W8 W9 WA WB WC WD WE WF WG WH WI WJ WK WL WM WN WO WP WR WS WT WU WV WW WY X0 X1 X2 X3 X4 X5 X7 X8 X9 XA XB XC XD XE XF XG XH XK XL XM XN XO XP XQ XR XS XT XU XV XW XX XY XZ Y0 Y1 Y2 Y4 Y5 Y6 Y9 YA YB YC YD YE YF YG YH YK YL YM YN YP YQ YR YS YT YX Z0 Z1 Z2 Z3 Z4 Z5 Z6 Z8 ZA ZB ZC ZD ZE ZF ZG ZH ZJ ZL ZM ZN ZP ZR ZS ZT ZU ZV ZW ZX ZY

Popular Components