EEWORLDEEWORLDEEWORLD

Part Number

Search

WBC-T0303AS-02-3880-CC

Description
Array/Network Resistor, Center Tap, Thin Film, 0.25W, 388ohm, 100V, 0.25% +/-Tol, -50,50ppm/Cel, 0303,
CategoryPassive components    The resistor   
File Size376KB,3 Pages
ManufacturerTT Electronics plc
Websitehttp://www.ttelectronics.com/
Environmental Compliance
Download Datasheet Parametric View All

WBC-T0303AS-02-3880-CC Overview

Array/Network Resistor, Center Tap, Thin Film, 0.25W, 388ohm, 100V, 0.25% +/-Tol, -50,50ppm/Cel, 0303,

WBC-T0303AS-02-3880-CC Parametric

Parameter NameAttribute value
Is it Rohs certified?conform to
Objectid802646061
Reach Compliance Codecompliant
ECCN codeEAR99
structureChip
Network TypeCenter Tap
Number of terminals6
Maximum operating temperature150 °C
Minimum operating temperature-55 °C
Package length0.762 mm
Package formSMT
Package width0.762 mm
method of packingTray
Rated power dissipation(P)0.25 W
resistance388 Ω
Resistor typeARRAY/NETWORK RESISTOR
seriesWBC(TAPPED)
size code0303
technologyTHIN FILM
Temperature Coefficient50 ppm/°C
Tolerance0.25%
Operating Voltage100 V
Wire Bondable
Chip Resistors
WBC Series
Discrete or tapped schematics
MIL inspection available
High resistor density
IRC Advanced Film Division
IRC’s WBC series wire bondable chip resistors are ideally suited for
the most demanding hybrid application. The WBC combines IRC’s
TaNSil
®
tantalum nitride thin film technology with silicon substrate processing to produce an extremely small
footprint device with the proven stability, reliability and moisture performance of IRC’s TaNSil
®
resistor film.
Available in a wide range of tolerances and temperature coefficients to fit a variety of hybrid circuit applica-
tions. Custom resistance values, sizes and schematics are available on request from the factory.
Physical Data
R0202 - Discrete
(0.508mm ±0.025)
0.020˝ ±0.001
Electrical Data
Absolute Tolerance
Absolute TCR
R
Package Power Rating
(@ 70°C)
Rated Operating Voltage
(not to exceed
P x R )
Operating Temperature
Back contact
Noise
Substrate Material
Top contact
Substrate Thickness
Aluminum
Gold
R0202 and
T0303
B0202
Passivation
to ±0.1%
to ±25ppm/°C
250mW
100V
-55°C to +150°C
<-30dB
Oxidized Silicon
(10KÅ SiO
2
min)
0.010˝ ±0.001
(0.254mm ±0.025)
10KÅ minimum
15KÅ minimum
Silicon
(Gold available)
Gold
3KÅ minimum
Silicon Dioxide or
Silicon Nitride
0.004˝ min bond pad size
0.020˝ ±0.001
(0.508mm ±0.025)
B0202 - Discrete back contact
(0.508mm ±0.025)
0.020˝ ±0.001
R
Top contact
pad chamfered
0.004˝ min bond pad size
0.020˝ ±0.001
(0.508mm ±0.025)
T0303 - Tapped network ½R + ½R
Bond Pad
Metallization
(0.762mm ±0.025)
0.030˝ ±0.001
Backside
½R
½R
0.030˝ ±0.001
(0.762mm ±0.025)
0.004˝ min bond pad size
General Note
IRC reserves the right to make changes in product specification without notice or liability.
All information is subject to IRC’s own data and is considered accurate at time of going to print.
© IRC Advanced Film Division
• Corpus Christi Texas 78411 USA
Telephone: 361 992 7900 • Facsimile: 361 992 3377 • Email: afdsales@irctt.com • Website: www.irctt.com
A subsidiary of
TT electronics plc
WBC Series Issue April 2006
Connecting to the database under wince
I connected to a database under wince and built a sqlce database. I need to connect to the database in the program, but I don't know how to connect. I'm new to databases and don't know much about them...
eddy326 Embedded System
MSP430 introductory textbook
...
buruno Microcontroller MCU
My graduation project defense is coming up soon, but I don’t know anything about my graduation project!!! What should I do?
My topic is the design of washing machine control circuit based on CPLDThe VHDL modular design method is used to design the washing machine controller, that is, from top to bottom, starting from the o...
boys FPGA/CPLD
Help: SN74HC164N output program problem:
I wrote a program for a single-chip microcomputer, which uses a 164 chip as an IO expansion port. I wrote a program like this for it to output some data. Can you take a look? ? ? serial input:P10; clo...
sawos Embedded System
Why can't I set breakpoints when debugging with ICD2 in MAPLAB?
Often a hollow red circle appears, and as soon as the program is run it reports that one or more breakpoints could not be resolved. Select breakpoints from the debugger menu for details? Also, can onl...
一诺千金 Embedded System
Read the good book "Operational Amplifier Parameter Analysis and LTspice Application Simulation" 04 Amplifier Noise Evaluation Case
[i=s]This post was last edited by 1nnocent on 2021-5-19 16:49[/i]Since I have had little exposure to weak signal amplification before, I don’t know much about this area. Now follow the example in 2.7....
1nnocent Analog electronics

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 2656  2199  1009  1023  462  54  45  21  10  31 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号