3mm Round
®
Optopipe
TM
Optical Light Pipe, Bi-Level
4.57
[.18]
1.52
[.06]
Ø 3.05
[.120] TYP
2 PLCS
3.05
[.120]
2.54
[.100]
DIFFUSED FRONT
SURFACES;
2 PLCS
5.08
[.200]
2.54
[.100]
2.79
[.11]
5.12
[.200]
2.29
[.090]
FRONT
PANEL
Ø 1.63
[.064]
MOUNTING
PIN
13.97
[.55]
1.91
[.075]
REF
7.62
[.300]
515-1061
Recommended
MicroLED SMT LEDs
for use with 515-1061
PART NO.
597-3111-5xx
597-3211-5xx
597-3301-5xx
597-3401-5xx
597-7701-5xx
597-7721-5xx
9.14
[.36]
1.57
[.062]
2
THIS VIEW SHOWS TWO 515-1061
LIGHT PIPES MOUNTED
SIDE BY SIDE
.25
[.010]
5.12
[.200]
7.87
[.310]
4.50
[.177]
TYP
2.54
[.100]
COLOR
AlGaAs Red
Orange
Green
Yellow
Red/Green
Yellow/Green
PAGE #
1-30
1-30
1-30
1-30
1-31
1-31
DIRECTION
OF LIGHT
3.35
[.132]
2.54
±.05
[.100
±.002]
4.27
[.168]
4.50
[.177]
1.45
[.057]
TYP
2.69
[.106]
TYP
1.04
[.041]
TYP
DIRECTION
OF LIGHT
1.60
[.063]
TYP
[Ø .060
±.002]
TYP, 2 PLCS
3.89
[.153]
Ø1.52
±.05
[.060
±.002]
TYP, 2 PLCS
3.73
[.147]
2.54
±.05
[.100
±.002]
4.39
[.173]
4.39
[.173]
TYP
FIGURE B
(USING BI-COLOR SMT LEDS)
NOTE: designed for
post-reflow
PC board insertion.
FIGURE A
(USING SINGLE COLOR SMT LEDS)
RECOMMENDED SOLDER PAD/HOLES LAYOUT
RECOMMENDED SOLDER PAD/HOLES LAYOUT
Dimensions in mm [inches]
Features
• Can be mounted in arrays spaced .200 apart (min.)
• High transmissivity polycarbonate material
• UL94V-0 compliance
• ESD protection (circuit isolation from front panel)
• Wide viewing angle
• Arrays reduce insertion costs
• Allows bi-level SMT indicators
• Secures to PCB by press-fit
LED Data
For absolute maximum ratings and other
electrical and optical data on the recommended
LEDs, refer to LED data sheets.
Operating/Storage Temperature
–30°C to +100°C
Dialight
Optopipe
Light Pipe Description
This Optopipe™ is a standard design intended as a SMT compatible replacement for our 553 Series Circuit Board
Indicators. The light outputs are spaced vertically .100" from the PCB to the first element, and then 0.200" between the top
and bottom elements. We recommend a minimum of 0.200" between light pipes as a normal mounting pitch. This
Optopipe™ is held in place by 2 press-fit pins along the bottom of the device. The light pipe is not attached to the panel at
any point but can protrude through holes in the panel. The gently arcing emitting end sticks through the plastic or metal
panel. The light source is Dialight's 597 Series Type 1208 LED. The light pipe material is water clear transmissive
polycarbonate rated UL94-V0, and has a 35% oxygen index.
Dialight can provide custom Optopipe™ solutions for your applications.
Dialight Corporation • 1501 Route 34 South • Farmingdale, NJ 07727 • TEL: (732) 919-3119 • FAX: (732) 751-5778 •www.dialight.com
2-43
Talking about work
京公网安备 11010802033920号
EEWORLD
