refer to the LIST OF PART NUMBERS when placing orders.
■
Specifications are subject to change without notice.
COPAL ELECTRONICS
SURFACE MOUNT TRIMMERS
SM-42/43
■
LIST OF PART NUMBERS
Electrical turn
Adjustment
Shape of terminal
position
Form of packaging
Taping (reel)
Plastic bag
〈
Nominal resistance values
〉
A
10
Ω
A
20
Ω
50
Ω
100
Ω
200
Ω
500
Ω
1 kΩ
2 kΩ
2 MΩ
5 kΩ
10 kΩ
20 kΩ
50 kΩ 100 kΩ 200 kΩ 500 kΩ 1 MΩ
Fig. 1
W
(J-hook)
Top adjustment
SM-42TW
SM-42TX
SM-42TA
SM-42TB
SM-43TW
SM-43TX
SM-43TA
SM-43TB
TA, TB : 500 pcs./reel
TW, TX : 250 pcs./reel
SM-42W
SM-42X
SM-42A
SM-42B
SM-43W
SM-43X
SM-43A
SM-43B
X
(Gull wing)
11
A
(J-hook)
Side adjustment
The products indicated by
A
mark are manufactured upon receipt of order basis.
※The
above part numbers are all available with the respective combination of
<Nominal resistance values> (Fig. 1).
※Verify
the above part numbers when placing orders.
※Taping
specification is not sold separately and must be purchased in reel units.
B
(Gull wing)
W
(J-hook)
Top adjustment
X
(Gull wing)
5
A
(J-hook)
Side adjustment
■
MECHANICAL CHARACTERISTICS
Operating torque
17.6 mN·m {180 gf·cm} maximum
Clutch action
200 cycles [
Δ
R/R
≦
±
(3
Ω +3
%)]
5 N {0.51 kgf} minimum
245
±
3 °C, 2 ~ 3 s
5 N {0.51 kgf} 10 s
Width 90 mm, bend 3 mm, 5 s, 1 time
5 N {0.51 kgf} 10 s
{ }
：
Reference only
Mechanical stop
Rotational life
B
(Gull wing)
Pieces in package
50 pcs./pack
■
ELECTRICAL CHARACTERISTICS
Nominal resistance range
Resistance tolerance
Power ratings
Resistance law
Maximum input voltage
Maximum wiper current
Effective electrical turn
End resistance
C.R.V.
Operating temp. range
Temp. coefficient
Insulation resistance
Dielectric strength
Net weight
10
Ω
~ 2 MΩ
±
10 %
0.25 W (85 °C) 0 W (150 °C)
Linear law
DC300 V or power rating, whichever is smaller
100 mA or power rating, whichever is smaller
11 turns (SM-42), 5 turns (SM-43)
1 % or 2
Ω,
whichever is greater
1 % or 3
Ω,
whichever is greater
−65
~ 150 °C
±
100 10
-6
/°C maximum
100 MΩ minimum (DC500 V)
AC600 V, 60 s
Approx. 0.17 g
Thrust to shaft
Solderability
Shear (Adhesion)
Substrate bending
Pull-off strength
■
ENVIRONMENTAL CHARACTERISTICS
Test item
Thermal shock
Humidity
Shock
Vibration
Load life
Low temp. operation
High temp. exposure
Test conditions
−65
~ 150 °C (0.5 h), 5 cycles
−10
~ 65 °C (80 ~ 98 %),
10 cycles, 240 h
981 m/s
2
, 6 ms
6 directions for 3 times each
Amplitude 1.52 mm or
Acceleration 196 m/s
2
,
10 ~ 2000 Hz, 3 directions, 12 times each
Specifications
[
Δ
R/R
≦
2 %]
[S.S.
≦
1 %]
[
Δ
R/R
≦
2 %]
[
Δ
R/R
≦
1 %]
[S.S.
≦
1 %]
[
Δ
R/R
≦
3 % or 3
Ω]
[S.S.
≦
2 %]
[
Δ
R/R
≦
1 %]
[S.S.
≦
1 %]
[
Δ
R/R
≦
2 %]
[S.S.
≦
1 %]
No leaks (No continuous bubbles)
85 °C, 0.25 W, 1000 h
−65
°C, 2 h
150 °C, 250 h
85 °C, 60 s
Reflow profile for soldering heat evaluation
〉
(°C)
250
Temperature
200
150
100
50
Peak : 250
+5
0
Immersion seal
°C
Over 230
°C
180
°C
150
°C
Pre Heating Zone
Soldering heat
90
±
30 s
30
±
10 s
Heating time
Soldering Zone
Reflow : Peak temperature 255 °C
(Please refer to the profile below.)
Manual soldering：
350
±
10 °C, 3 ~ 4 s
[
Δ
R/R
≦
1 %]
Δ
R/R：Change in total resistance
S.S.
：Setting
stability
Reflow : two times maximum
■
Specifications are subject to change without notice. Specifications in this catalog are for reference. The formal specification sheets will be submitted upon request.
COPAL ELECTRONICS
SURFACE MOUNT TRIMMERS
SM-42/43
■
MAXIMUM INPUT RATINGS
Nominal resistance
input
Resistance code Maximum (V)
values (Ω)
voltage
A
A
10
20
50
100
200
500
1k
2k
5k
10 k
20 k
50 k
100 k
200 k
500 k
1M
2M
100
200
500
101
201
501
102
202
502
103
203
503
104
204
504
105
205
1.00
2.00
3.53
5.00
7.07
11.2
15.8
22.4
35.4
50.0
70.7
112
158
223
300
300
300
Maximum wiper
current (mA)
100
100
70.7
50.0
35.4
22.4
15.8
11.2
7.07
5.00
3.54
2.24
1.58
1.12
0.60
0.30
0.15
The products indicated by
A
mark are manufactured upon receipt of order basis.
■
RECOMMENDED P.C.B. PAD OUTLINE DIMENSIONS
●
SM-42/43A
2
2
(Unit: mm)
●
SM-42/43B
1.3
2
●
SM-42/43W
●
SM-42/43X
2
1.9
1.6
2.9
0
1.6
2.54
2
5.2
0
0
0
2
1.3
2.3
2.3
1.3
2.54
Note) The zero point is the center of mounting.
■
Specifications are subject to change without notice. Specifications in this catalog are for reference. The formal specification sheets will be submitted upon request.
1.9
1.3
1.3
1.3
5.1
4
COPAL ELECTRONICS
SURFACE MOUNT TRIMMERS
SM-42/43
■
OUTLINE DIMENSIONS
●
SM-42/43W
3.9
3.5
1
Resistance code & Production date code
2
1.3
Unless otherwise specified, tolerance :
±
0.3 (Unit : mm)
1
2
3
CW rotation
※
Note the terminal position.
2.54
1.2
4.8
2 – 0.8
3
2.6
φ
1.5, Slot
0.56W
×
0.5D
5.1
5.3
3 – 0.9
3–1
●
SM-42/43X
5.7
3.5
Resistance code & Production date code
2
1.3
1
2.54
2 – 0.8
3
φ
1.5, Slot
0.56W
×
0.5D
1.2
5.1
5.3
3–1
●
SM-42/43A
Resistan ce code & Produ ction d ate code
①
3–1
2.3
2 – 0.9
1.2
1.3
0.56W
×
0.5D
2.6
3.7
3 – 0.8
②
φ
1.5, Slot
③
4.6
5
●
SM-42/43B
Resistance code & Production date code
2
1
3.9
4.8
4.8
2.3
1.3
4.8
2 – 0.9
φ
1.5, Slot
2.8
0.56W
×
0.5D
4.6
6
■
Specifications are subject to change without notice. Specifications in this catalog are for reference. The formal specification sheets will be submitted upon request.
1.2
3
3 – 0.6
COPAL ELECTRONICS
SURFACE MOUNT TRIMMERS
SM-42/43
■
PACKAGING SPECIFICATIONS
<Taping packaging specifications>
●
Taping version (SM-42/43TA, TB) is packaged in 500 pcs. per reel.
Orders will be accepted for units of 500 pcs., i.e., 500, 1000, 1500 pcs., etc.
SM-42/43TW, TX is packaged in 250 pcs. per reel.
Orders will be accepted for units of 250 pcs., i.e., 500, 750 pcs., etc.
Maximum number of consecutive missing pieces = 2
Leader length and reel dimension are shown in the dia-grams below.
●
EMBOSSED TAPE DIMENSIONS
●
REEL DIMENSIONS
（Conforms
to JIS C 0806-3）
（TA/TB
type : In accordance with EIAJ ET-7200A）
Empty
Filled
Empty
+1
(Unit: mm)
13
0
(TA/TB)
17±0.3 (TW, TX)
21±0.8
2±0.5
End
40 mm min.
20 pitches min.
Leader
Head
400 mm min.
13±0.2
180
–1.5
(TA/TB)
0
180
–3
(TW, TX)
0
15.4±1 (TA/TB)
19.5±1 (TW/TX)
●
SM-42/43TW/TX
1.75
±
0.1
4
±
0.1
2
±
0.1
.5
φ
1
●
SM-42/43TA/TB
1.75
±
0.1
0.5
±
0.1
Installation
example
(SM-42W)
1
4
±
0.1
2
±
0.1
3
A
0.4
±
0.1
Installation
example
(SM-42A)
A
3
7.5
±
0.1
5.5
±
0.05
16
–0.1
+0.3
12
60
φ
5
1.
.1
+0 0
Direction of feed
+1
0
.1
+0 0
2
A
1
12
±
0.1
5.75
Cross section A-A
2
A
8
±
0.1
4.5
Cross section A-A
<Bulk pack specifications>
●
Unit of bulk in a plastic bag is 50 pcs. per pack.
●
Boxing of bulk in a plastic bag is performed with 200 pcs. per box.
■
Specifications are subject to change without notice. Specifications in this catalog are for reference. The formal specification sheets will be submitted upon request.
I am touched by astwyg's enthusiasm, and I hope this forum will get better and better under his leadership! Personal information: [url]https://home.eeworld.com.cn/space.php?uid=272563&op=bbs[/url] Wel...
I input the sine wave into an 8-bit AD (AD9280) and then directly connected it to an 8-bit DA (AD9708). I found that the waveform was distorted. What is the reason?...
Use the Unicore LC6311 TD-SCDMA module on the WinCE platform to perform GPRS dialing and call the following function wstring wsEntryName = s2w("TDSCD"); wstring wsUserName = s2w(""); wstring wsPasswor...
[i=s]This post was last edited by paulhyde on 2014-9-15 09:42[/i] How to use 51 single chip microcomputer to analyze the amplitude, frequency and slope of triangle wave? Please give me some advice....
When compiling evc, it needs to link to the simulator. I cancelled the link, and then the problem came: I often couldn't connect when debugging later. Usually, it connected this time, quit debugging, ...
I. Introduction
Since RS232 has a short communication distance (only 15 meters according to EAT/TAI-232 standard), and can only perform point-to-point communication, it cannot directly f...[Details]
LED lamps and bulbs are now rapidly replacing incandescent, halogen and CFL (compact fluorescent lamp) light sources in many general lighting applications. Flyback DC/DC converters are the power su...[Details]
Digital array radar (DAR) uses digital beam forming (DBF) in both receiving and transmitting modes to achieve flexible distribution and reception of RF signal power in the airspace, obtain excellent t...[Details]
TC9012F is a universal CMOS large-scale integrated circuit for infrared remote control signal transmission, suitable for remote control of TV, VTR, laser player and other equipment. In the market, ...[Details]
The rectified DC voltage is then converted back to AC using power electronics such as insulated gate bipolar transistors.
The output voltage is switched on and off at a high frequency, control...[Details]
Liquid crystal display (LCD) panels have a wide range of applications, from small portable electronic devices to large fixed devices, including digital cameras, laptops, personal data assistants, d...[Details]
At present, how various communication technologies will evolve after 3G is a focus of great concern in the industry. Especially for TD-SCDMA, whether it can achieve smooth evolution to the next gen...[Details]
When the so-called "copycat phones" that flood the domestic mobile phone market move towards large screens, stereo amplifiers, touch controls, and even GPS navigation and mobile TV, the homogeneity...[Details]
1 Development of LED Film and Television Lighting
1.1 The significance of developing film and television lighting
Lighting power consumption accounts for a large proportion of the total p...[Details]
In order to prevent the lithium battery from being damaged by abnormal conditions such as overcharge, over discharge, and overcurrent, a lithium battery protection device is usually used to prevent...[Details]
Mobile phones, MP3s, tablet computers, laptops, digital cameras, handheld game consoles, navigation devices, etc., all these mobile devices are powered by mobile batteries, and the battery life is ...[Details]
In industry, voltage 0…5 (10) V or current 0 (4)…20 mA is usually used as a method for analog signal transmission, which is also a method often used by programmable controllers. So what are the dif...[Details]
1 Introduction
Power supply ripple will interfere with the normal operation of electronic equipment, causing malfunctions such as computer crashes, data processing errors and control system fa...[Details]
The principles to be followed are as follows:
(1) In terms of component layout, related components should be placed as close as possible. For example, clock generators, crystal oscillat...[Details]
1 Introduction
Fieldbus is a serial, digital, multi-point communication data bus between field equipment/instruments installed in the production process area and automatic control devices/syst...[Details]
Electronics Design Contest
京公网安备 11010802033920号
EEWORLD
