EEWORLDEEWORLDEEWORLD

Part Number

Search

14930A0BJFA13254KF

Description
Potentiometer, Cermet, 1W, 250000ohm, 10% +/-Tol, -150,150ppm/Cel, 4935,
CategoryPassive components    The resistor   
File Size148KB,5 Pages
ManufacturerVishay
Websitehttp://www.vishay.com
Environmental Compliance
Download Datasheet Parametric View All

14930A0BJFA13254KF Overview

Potentiometer, Cermet, 1W, 250000ohm, 10% +/-Tol, -150,150ppm/Cel, 4935,

14930A0BJFA13254KF Parametric

Parameter NameAttribute value
Is it Rohs certified?conform to
Objectid967705984
Reach Compliance Codecompliant
Country Of OriginCzechia
YTEOL8
structureTrimmer Pot
JESD-609 codee3
Lead length8.85 mm
Maximum operating temperature125 °C
Minimum operating temperature-40 °C
Package height13.1 mm
Package length12.5 mm
Package formPCB Mount
Package width8.83 mm
method of packingBox
Rated power dissipation(P)1 W
resistance250000 Ω
Resistor typePOTENTIOMETER
rotation angle270 deg
series149
size code4935
technologyCERMET
Temperature Coefficient150 ppm/°C
Terminal surfaceTin (Sn)
Tolerance10%
148, 149
Vishay Spectrol
1/2" (12.7 mm) Conductive Plastic and Cermet
Potentiometer
FEATURES
Robust construction
High rotational life (50 000 cycles)
Up to three sections PC support plates
Rotary switches and solder lugs terminals available
Tests according to CECC 41000 or IEC 60393-1
Compliant to RoHS Directive 2002/95/EC
148 FEATURES
Conductive plastic element
Quiet electrical output
149 FEATURES
Cermet element
Low temperature coefficient (± 150 ppm/°C)
DIMENSIONS
in millimeters (inches) ± 0.5 mm (± 0.02"
)
Single, dual or triple
12.5
(0.492)
0.8
(0.031)
12.5
(0.492)
Solder lug terminals
16.45
(0.648)
12.5
(0.492)
6.35
(0.250)
1.2
(0.047)
8.0
(0.315)
4.900
(0.193)
4.7
(0.185)
8.83
(0.348)
9.52
(0.375)
8.85
(0.341)
12.5
(0.492)
0.6
(0.024)
0.6
(0.024)
0.6
(0.024)
2.54
(0.100)
1 2 3
2.54
(0.100)
0.30
(0.012)
5.07
(0.200)
3.17
(0.125)
2.4
(0.094)
Thread 1/4 32-NEF-2A
7.62
(0.300)
0.9
(0.035)
1.800
(0.071)
4.65
(0.183)
1
2
3
0.300
(0.012)
4.770
(0.188)
Thread 3/8 32-NEF-2A
4.65
(0.183)
Front and rear support plates
E = Flush with board surface
4.70
(0.185)
12.5
(0.492)
0.80
(0.031)
Dual
Single
0.60
(0.024)
12.50
(0.492)
2.54
(0.100)
5.08
(0.200)
1 2 3
2.54
(0.100)
5.08
(0.200)
6.35
(0.250)
7.62
(0.300)
1.52
(0.06)
3.85
(0.151)
6.35
(0.250)
1.52
(0.06)
3.85
(0.151)
www.vishay.com
102
Document Number: 57040
For technical questions, contact:
sfer@vishay.com
See also Application Notes:
www.vishay.com/doc?51001
and
www.vishay.com/doc?52029
Revision: 05-May-11
This document is subject to change without notice.
THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT
www.vishay.com/doc?91000
6.35
(0.250)
Car active safety devices fully explained
When buying a car, I believe everyone will be very concerned about the safety performance of the car. After all, with the increase in the number of vehicles, traffic accidents are also increasing, and...
zzloveff Automotive Electronics
TM4C123GH6PM GPIO interrupt and IIC cannot be shared
Set PORTA as IIC interfaceSysCtlPeripheralEnable(SYSCTL_PERIPH_I2C1); //Enable I2C1 SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOA); //Enable PA6 GPIOPinConfigure(GPIO_PA6_I2C1SCL); //Configure PA6 as I2C...
zhang_edgar Microcontroller MCU
Can an expert help me see why 1602 is not displayed?
;File name: LCD1301.ASM ;Program function: Display "OK" program RS bit P1.0 RW bit P1.1 E bit P1.2 LCD EQU P0 MAIN: ;Main program MOV LCD,#00000001B ;Clear the screen and reset the cursor ACALL WR_COM...
qiushui Embedded System
Basic points of constant magnetic field
When a constant current flows through a conductor, there is not only a constant electric field inside the conductor and in the medium around it, but also a magnetic field that does not change with tim...
fighting Analog electronics
Using timer A and timer B simultaneously
My design requires two timers. Timer A has a timing interval of 10ms. The interrupt service program of timer A implements AD conversion, making the sampling frequency of AD conversion reach 100HZ.The ...
随便 Microcontroller MCU
I have ported the power part of HeartRate to sensortag 1.4, but it always shows 0. Has anyone ported it before?
Has anyone transplanted it before? Please share your experience....
jameslin Wireless Connectivity

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 2881  1473  270  377  2728  59  30  6  8  55 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号