PVZ3G471C01R00 datasheet, PDF - EEWORLD Datasheet

Datasheet> All Categories > Passive components> PVZ3G471C01R00

PVZ3G471C01R00: Descriptiontrimmer 470 ohm 0.1W smd; CategoryPassive components; File Size182KB，12 Pages; ManufacturerMurata; Websitehttps://www.murata.com; Environmental Compliance

Download Datasheet Parametric View All

PVZ3G471C01R00 Overview

trimmer 470 ohm 0.1W smd

PVZ3G471C01R00 Parametric

Parameter Name	Attribute value
Datasheets
PVZ3GyyyC01 Series
Trim Pots, Part Numbering
Trimmer Potentiometers Catalog
Product Photos
PVZ3G Series
Catalog Drawings
PVZ3(A,G) Series Circui
PVZ3G Series T
PVZ3G Series Side
Standard Package	1
Category	Potentiometers, Variable Resistors
Family	Trimmer Potentiometers
Packaging	Digi-Reel®
Resistance (Ohms)	470
Power (Watts)	0.1W, 1/10W
Tolerance	±30%
Temperature Coefficie	±500ppm/°C
Number of Turns	Single
Adjustment Type	Top Adjustme
Resistive Material	Carb
Mounting Type	Surface Mou
Termination Style	J Lead
Size / Dimensi	Square - 0.122" x 0.122" Face x 0.045" H (3.10mm x 3.10mm x 1.15mm)
Other Names	490-4627-6

Preview

Download Datasheet

View All

UNCONTROLLED

COPY

REFERENCE ONLY

SPECIFICATION FOR SUPPLIED PRODUCT

SPECIFICATION No. JVR03Z-7148B

TRIMMER POTENTIOMETER / PVZ3G

C01 SERIES

-CONTENTS-

1. SCOPE

2. MURATA PART NUMBER

3. OUTLINE DIMENSIONS AND MARKINGS

4. CHARACTERISTICS

4.1

4.2

4.3

4.4

Electrical Characteristics

Mechanical Characteristics

Environmental Characteristics

Other Characteristics

5. TEST METHOD

5.1

5.2

5.3

5.4

5.5

5.6

5.7

5.8

5.9

5.10

5.11

5.12

5.13

Contact Resistance Variation (CRV)

Temperature Coefficient of Resistance

Permitted Force of Driver Plate

Soldering Strength

High Temperature Exposure

Humidity Exposure

Load Life

Humidity Load Life

Temperature Cycle

Rotational Life

Vibration

Resistance to Soldering Heat

Solderability

6. CAUTION

7. CAUTION FOR USING

7.1

7.2

7.3

7.4

7.5

7.6

7.7

Mounting the product

Soldering

Cleaning

Adjusting

Operating Environmental Conditions

Storage Conditions

Circuit Design Guide

8. NOTICE

9. OUTLINE DIMENSIONS

10. TAPING SPECIFICATIONS

10.1 Plastic Tape Dimensions

10.2 Reel Dimensions

11. PART NUMBERS CROSS REFERENCE TABLE

1/12

UNCONTROLLED

COPY

REFERENCE ONLY

5.5 High temperature exposure

SPECIFICATION No. JVR03Z-7148B

The wiper contact point should be preset at about 50% position of effective rotational angle. After that, the

trimmer potentiometer should be kept in a chamber at 70±2°C without loading for 500±12 hours. The

resistance value should be measured after keeping the trimmer potentiometer in a room for 1.5±1/6 hours.

5.6 Humidity exposure

The wiper contact point should be preset at about 50% position of effective rotational angle. After that,

the trimmer potentiometer should be kept in a chamber at 40±2°C and 90 to 95% without loading for 500±12

hours. The resistance value should be measured after keeping the trimmer potentiometer in a room for 5±1/6

hours.

5.7 Load life

The wiper contact point should be preset at about 50% position of effective rotational angle. After that, the

trimmer potentiometer should be kept in a chamber at 50±2°C with loading the 1/2 rated voltage between #1

and #2 terminals, intermittently 1.5 hours ON and 0.5 hours OFF for 1000±12 hours. The resistance value

should be measured after keeping the trimmer potentiometer in a room for 1.5±1/6 hours.

5.8 Humidity load life

The wiper contact point should be preset at about 50% position of effective rotational angle. After that, the

trimmer potentiometer should be kept in a chamber at 40±2°C and 90 to 95% with loading the 1/2 rated voltage

between #1 and #2 terminals, intermittently 1.5 hours ON and 0.5 hours OFF for 1000±12hours.

The resistance value should be measured after keeping the trimmer potentiometer in a room for 5±1/6 hours.

5.9 Temperature cycle

The wiper contact point should be preset at about

50% position of effective rotational angle. After that,

the trimmer potentiometer should be subjected to

Table 2 temperatures for 5 cycles. The resistance

value should be measured after keeping the trimmer

potentiometer in a room for 1.5±1/6 hours.

Sequence

Temp. (°C)

Time (min.)

Table 2

-25±3

+25±2

30±3 10 max.

+85±3

30±3

+25±2

10 max.

5.10 Rotational life

The wiper should be rotated over 90% of the effective rotational angle without loading at a speed of 10 cycles

per minute, for 10 cycles continuously. The resistance value should be measured after keeping the trimmer

potentiometer in a room for 10±5 minutes.

5.11 Vibration

The wiper contact point should be preset at about 50% position of effective rotational angle. After that, the

trimmer potentiometer should be tested under the condition of the amplitude of 1.5mm, the frequency range

from 10 to 55Hz (shall be traversed in approximately one minute) and 2 hours in each of 3 mutually

perpendicular directions. (Total 6 hours)

5/12

Recommended Resources

Half-wave rectifier circuit with filter capacitor

Homemade color changing light circuit

Using a constant current source to complete the level shift circuit diagram

Pulse motor unidirectional rotation control and interface circuit

Eliminate DC solenoid sparks

Power supply soft start circuit using capacitor

Sure seal waterproof connector: The company operates a full range of Sure seal waterproof connectors, including industrial/military fields. Specifically, there are the following series: Sure seal is mainly used for cable connections...; yunsa001 Automotive Electronics

MSP430 Watchdog Program Analysis: The chip is MSP430F2274, watchdog program, why is the delay 2s? Please analyze it, thank you* WDTCTL = WDT_ADLY_1000; //Interval timer, timing 1000ms //Delay 2s for(i = 0; i < 3; i++) { IFG1 &= ~WDTIF...; 火火山 Microcontroller MCU

Learn about switching power supply testing: [p=30, null, left][font=宋体][color=#a0522d]In electronic environments, electromagnetic interference will have a certain impact on the operation of power supplies. Power supplies with small source effec...; qwqwqw2088 Analogue and Mixed Signal

How to interpret the carrier suppression degradation indicator in the transmitter?: In the transmitter indicators: carrier suppression deterioration is less than 3dB. What I want to ask here is what is the main cause of the transmitter carrier suppression deterioration? Please give m...; ywtwd RF/Wirelessly

"【Play esp8266 together】+Learn esp8266": [b]25E[/b] I received it from esp8266, I didn't have much hope at first.I really appreciate the benefits of this forum.I received the stuff, thanks to everyone in this forum.I picked up the phone, com...; bjwl_6338 MicroPython Open Source section

2440+UDA1341 mic: The audio signal is input from the ADC input of UDA1341, and then output from the DAC output of 1341. The main purpose is to control the volume\bass\treble\mute of the input signal through 1341, and s...; colin_cx Embedded System

Shortcut: S0 S1 S2 S3 S4 S5 S6 S7 S8 S9 SA SB SC SD SE SF SG SH SI SJ SK SL SM SN SO SP SQ SR SS ST SU SV SW SX SY SZ T0 T1 T2 T3 T4 T5 T6 T7 T8 T9 TA TB TC TD TE TF TG TH TI TJ TK TL TM TN TO TP TQ TR TS TT TU TV TW TX TY TZ U0 U1 U2 U3 U4 U6 U7 U8 UA UB UC UD UE UF UG UH UI UJ UK UL UM UN UP UQ UR US UT UU UV UW UX UZ V0 V1 V2 V3 V4 V5 V6 V7 V8 V9 VA VB VC VD VE VF VG VH VI VJ VK VL VM VN VO VP VQ VR VS VT VU VV VW VX VY VZ W0 W1 W2 W3 W4 W5 W6 W7 W8 W9 WA WB WC WD WE WF WG WH WI WJ WK WL WM WN WO WP WR WS WT WU WV WW WY X0 X1 X2 X3 X4 X5 X7 X8 X9 XA XB XC XD XE XF XG XH XK XL XM XN XO XP XQ XR XS XT XU XV XW XX XY XZ Y0 Y1 Y2 Y4 Y5 Y6 Y9 YA YB YC YD YE YF YG YH YK YL YM YN YP YQ YR YS YT YX Z0 Z1 Z2 Z3 Z4 Z5 Z6 Z8 ZA ZB ZC ZD ZE ZF ZG ZH ZJ ZL ZM ZN ZP ZR ZS ZT ZU ZV ZW ZX ZY

Popular Components