PVZ3G682C01R00 datasheet, PDF - EEWORLD Datasheet

Datasheet> All Categories > Passive components> PVZ3G682C01R00

PVZ3G682C01R00: Descriptiontrimmer 6.8K ohm 0.1W smd; CategoryPassive components; File Size182KB，12 Pages; ManufacturerMurata; Websitehttps://www.murata.com; Environmental Compliance

Download Datasheet Parametric View All

PVZ3G682C01R00 Overview

trimmer 6.8K ohm 0.1W smd

PVZ3G682C01R00 Parametric

Parameter Name	Attribute value
Datasheets
PVZ3GyyyC01 Series
Trim Pots, Part Numbering
Product Photos
PVZ3G Series
Catalog Drawings
PVZ3(A,G) Series Circui
PVZ3G Series T
PVZ3G Series Side
Standard Package	2,500
Category	Potentiometers, Variable Resistors
Family	Trimmer Potentiometers
Packaging	Tape & Reel (TR)
Resistance (Ohms)	6.8k
Power (Watts)	0.1W, 1/10W
Tolerance	±30%
Temperature Coefficie	±500ppm/°C
Number of Turns	Single
Adjustment Type	Top Adjustme
Resistive Material	Carb
Mounting Type	Surface Mou
Termination Style	J Lead
Size / Dimensi	Square - 0.122" x 0.122" Face x 0.045" H (3.10mm x 3.10mm x 1.15mm)
Other Names	490-4632-2

Preview

Download Datasheet

View All

UNCONTROLLED

COPY

REFERENCE ONLY

SPECIFICATION FOR SUPPLIED PRODUCT

SPECIFICATION No. JVR03Z-7148B

TRIMMER POTENTIOMETER / PVZ3G

C01 SERIES

-CONTENTS-

1. SCOPE

2. MURATA PART NUMBER

3. OUTLINE DIMENSIONS AND MARKINGS

4. CHARACTERISTICS

4.1

4.2

4.3

4.4

Electrical Characteristics

Mechanical Characteristics

Environmental Characteristics

Other Characteristics

5. TEST METHOD

5.1

5.2

5.3

5.4

5.5

5.6

5.7

5.8

5.9

5.10

5.11

5.12

5.13

Contact Resistance Variation (CRV)

Temperature Coefficient of Resistance

Permitted Force of Driver Plate

Soldering Strength

High Temperature Exposure

Humidity Exposure

Load Life

Humidity Load Life

Temperature Cycle

Rotational Life

Vibration

Resistance to Soldering Heat

Solderability

6. CAUTION

7. CAUTION FOR USING

7.1

7.2

7.3

7.4

7.5

7.6

7.7

Mounting the product

Soldering

Cleaning

Adjusting

Operating Environmental Conditions

Storage Conditions

Circuit Design Guide

8. NOTICE

9. OUTLINE DIMENSIONS

10. TAPING SPECIFICATIONS

10.1 Plastic Tape Dimensions

10.2 Reel Dimensions

11. PART NUMBERS CROSS REFERENCE TABLE

1/12

UNCONTROLLED

COPY

REFERENCE ONLY

5.5 High temperature exposure

SPECIFICATION No. JVR03Z-7148B

The wiper contact point should be preset at about 50% position of effective rotational angle. After that, the

trimmer potentiometer should be kept in a chamber at 70±2°C without loading for 500±12 hours. The

resistance value should be measured after keeping the trimmer potentiometer in a room for 1.5±1/6 hours.

5.6 Humidity exposure

The wiper contact point should be preset at about 50% position of effective rotational angle. After that,

the trimmer potentiometer should be kept in a chamber at 40±2°C and 90 to 95% without loading for 500±12

hours. The resistance value should be measured after keeping the trimmer potentiometer in a room for 5±1/6

hours.

5.7 Load life

The wiper contact point should be preset at about 50% position of effective rotational angle. After that, the

trimmer potentiometer should be kept in a chamber at 50±2°C with loading the 1/2 rated voltage between #1

and #2 terminals, intermittently 1.5 hours ON and 0.5 hours OFF for 1000±12 hours. The resistance value

should be measured after keeping the trimmer potentiometer in a room for 1.5±1/6 hours.

5.8 Humidity load life

The wiper contact point should be preset at about 50% position of effective rotational angle. After that, the

trimmer potentiometer should be kept in a chamber at 40±2°C and 90 to 95% with loading the 1/2 rated voltage

between #1 and #2 terminals, intermittently 1.5 hours ON and 0.5 hours OFF for 1000±12hours.

The resistance value should be measured after keeping the trimmer potentiometer in a room for 5±1/6 hours.

5.9 Temperature cycle

The wiper contact point should be preset at about

50% position of effective rotational angle. After that,

the trimmer potentiometer should be subjected to

Table 2 temperatures for 5 cycles. The resistance

value should be measured after keeping the trimmer

potentiometer in a room for 1.5±1/6 hours.

Sequence

Temp. (°C)

Time (min.)

Table 2

-25±3

+25±2

30±3 10 max.

+85±3

30±3

+25±2

10 max.

5.10 Rotational life

The wiper should be rotated over 90% of the effective rotational angle without loading at a speed of 10 cycles

per minute, for 10 cycles continuously. The resistance value should be measured after keeping the trimmer

potentiometer in a room for 10±5 minutes.

5.11 Vibration

The wiper contact point should be preset at about 50% position of effective rotational angle. After that, the

trimmer potentiometer should be tested under the condition of the amplitude of 1.5mm, the frequency range

from 10 to 55Hz (shall be traversed in approximately one minute) and 2 hours in each of 3 mutually

perpendicular directions. (Total 6 hours)

5/12

Recommended Resources

Low voltage lamp timing flashing circuit using programmable thyristor

CB3463 combined semi-automatic turret lathe electrical schematic circuit 03

Equivalent circuit and equivalent functional block diagram of bipolar 555/556

555 overvoltage indication circuit

555 power intermittent controller circuit

Water Activated Alarm

Looking for 51 new moderators!!: You read it right, I, the current 51 moderator, am looking for a new moderator.Because of work, I began to gradually distance myself from 51 - although my understanding and knowledge of 51 has always ...; 辛昕 51mcu

Zigbee fixed PANID: Hello, I want to fix the PANID of all nodes in the system, that is, when the old coordinator is broken. After the new coordinator is replaced, it can communicate with the nodes directly. 1. How to fix...; yuyueha Wireless Connectivity

Prize-giving event: Blind box delivery | Murata’s Pet Pink Month is officially launched!: Event time: From now until January 31, 2022 Go to participate How to participate: 1. Click the "I want to participate" button on the page and fill in the form to start the charging journey;2. Complete...; EEWORLD社区 Integrated technical exchanges

AD packaging for self-use HR911105A 100M and HR911130A 1000M network ports: AD packaging for self-use HR911105A 100M and HR911130A 1000M network ports The default direction is reverse, which can be converted to the front....; 机械老鼠 PCB Design

C language programming for microcontrollers and related training tutorials + embedded development related technical videos: C language programming for single-chip microcomputer and related training tutorials + embedded development related technical videos [C language programming for single-chip microcomputer and circuit de...; yingzi9 MCU

How much memory is needed to create an ISIS instance? Please help, thank you.: rt, on the switch...; whili Embedded System

Shortcut: E0 E1 E2 E3 E4 E5 E6 E7 E8 E9 EA EB EC ED EE EF EG EH EI EJ EK EL EM EN EO EP EQ ER ES ET EU EV EW EX EY EZ F0 F1 F2 F3 F4 F5 F6 F7 F8 F9 FA FB FC FD FE FF FG FH FI FJ FK FL FM FN FO FP FQ FR FS FT FU FV FW FX FY FZ G0 G1 G2 G3 G4 G5 G6 G7 G8 G9 GA GB GC GD GE GF GG GH GI GJ GK GL GM GN GO GP GQ GR GS GT GU GV GW GX GZ H0 H1 H2 H3 H4 H5 H6 H7 H8 HA HB HC HD HE HF HG HH HI HJ HK HL HM HN HO HP HQ HR HS HT HU HV HW HX HY HZ I1 I2 I3 I4 I5 I6 I7 IA IB IC ID IE IF IG IH II IK IL IM IN IO IP IQ IR IS IT IU IV IW IX J0 J1 J2 J6 J7 JA JB JC JD JE JF JG JH JJ JK JL JM JN JP JQ JR JS JT JV JW JX JZ K0 K1 K2 K3 K4 K5 K6 K7 K8 K9 KA KB KC KD KE KF KG KH KI KJ KK KL KM KN KO KP KQ KR KS KT KU KV KW KX KY KZ

Popular Components