EEWORLDEEWORLDEEWORLD

Part Number

Search

8N4S272EC-0126CDI8

Description
LVDS Output Clock Oscillator
CategoryPassive components    oscillator   
File Size599KB,18 Pages
ManufacturerIDT (Integrated Device Technology)
Environmental Compliance
Download Datasheet Parametric View All

8N4S272EC-0126CDI8 Overview

LVDS Output Clock Oscillator

8N4S272EC-0126CDI8 Parametric

Parameter NameAttribute value
Is it Rohs certified?conform to
Objectid1308558666
Reach Compliance Codecompliant
Other featuresENABLE/DISABLE FUNCTION; DIFFERENTIAL OUTPUT; TR
maximum descent time0.45 ns
Frequency Adjustment - MechanicalNO
frequency stability50%
Installation featuresSURFACE MOUNT
Nominal operating frequency19.2 MHz
Maximum operating temperature85 °C
Minimum operating temperature-40 °C
Oscillator typeLVDS
physical size7.0mm x 5.0mm x 1.55mm
longest rise time0.45 ns
Maximum supply voltage3.465 V
Minimum supply voltage3.135 V
Nominal supply voltage3.3 V
surface mountYES
maximum symmetry53/47 %
LVDS Frequency-Programmable
Crystal Oscillator
IDT8N4S272
DATA SHEET
General Description
The IDT8N4S272 is a Factory Frequency-Programmable Crystal
Oscillator with very flexible frequency programming capabilities. The
device uses IDT’s fourth generation FemtoClock
®
NG technology for
an optimum of high clock frequency and low phase noise
performance. The device accepts 2.5V or 3.3V supply and is
packaged in a small, lead-free (RoHS 6) 6-lead ceramic 5mm x 7mm
x 1.55mm package.
The device can be factory programmed to any in the range from
15.476MHz to 866.67MHz and from 975MHz to 1,300MHz and
supports a very high degree of frequency precision of 218Hz or
better. The extended temperature range supports wireless
infrastructure, telecommunication and networking end equipment
requirements.
Features
Fourth generation FemtoClock
®
NG technology
Factory-programmable clock output frequency from 15.476MHz to
866.67MHz and from 975MHz to 1,300MHz
Frequency programming resolution is 218Hz and better
One 2.5V, 3.3V LVDS clock output
Output enable control (positive polarity), LVCMOS/LVTTL
compatible
RMS phase jitter @ 231.25MHz (12kHz - 20MHz):
0.48ps (typical), integer PLL feedback configuration
RMS phase jitter @ 231.25MHz (1kHz - 40MHz):
0.50ps (typical), integer PLL feedback configuration
2.5V or 3.3V supply
-40°C to 85°C ambient operating temperature
Available in a lead-free (RoHS 6) 6-pin ceramic package
Block Diagram
PFD
&
LPF
FemtoClock
®
NG
VCO
1950-2600MHz
Pin Assignment
DNU 1
6 V
DD
5 nQ
4 Q
OSC
f
XTAL
2
÷P
÷N
Q
nQ
nOE 2
GND 3
÷MINT,
MFRAC
25
Configuration Register (ROM)
nOE
Pulldown
7
IDT8N4S272
6-lead ceramic 5mm x 7mm x 1.55mm
package body
CD Package
Top View
IDT8N4S272CCD
REVISION A OCTOBER 3, 2012
1
©2012 Integrated Device Technology, Inc.
[Xingkong Board Python Programming Learning Main Control Board] Evaluation 5: Burning System Image
[i=s]This post was last edited by Tianyiwuzui on 2022-11-13 20:30[/i]Before you start developing a board, in addition to understanding the basic knowledge of hardware architecture, you must also confi...
天意无罪 Embedded System
[Xingkong Board Python Programming Learning Control Panel] Review 6: Mind+ Programming Experience
Xingkong Board supports multiple programming methods, including: Mind+, jupyter, Thonny, SSH, etc.; Mind+ is a programming method that is strongly recommended by the official, because Mind+ supports g...
天意无罪 Embedded System
RF Integrated Balun Transformer Design
...
btty038 RF/Wirelessly
How about powering the MCU like this?
[i=s]This post was last edited by kal9623287 on 2022-11-14 09:11[/i]As shown in the figure below, if we consider the minimalist design to save cost, three diodes are connected in series, 5V power supp...
kal9623287 Power technology
I moved house and broke my computer...
I moved yesterday. I dropped my computer and the tempered glass shattered all over the floor because I didn't hold it steady. I didn't think the computer would break at the time. After arriving at the...
buildele Talking
What are the spacing requirements for drill holes in the fabrication of single-sided or double-sided PCBs?
The production of single-sided or double-sided PCBs is to drill non-conducting holes or conducting holes directly after cutting, while multi-layer boards are drilled after the pressing is completed. D...
东胜物联 PCB Design

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 1227  571  402  1006  1359  25  12  9  21  28 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号