EEWORLDEEWORLDEEWORLD

Part Number

Search

8N4S272EC-1033CD

Description
LVDS Output Clock Oscillator
CategoryPassive components    oscillator   
File Size599KB,18 Pages
ManufacturerIDT (Integrated Device Technology)
Environmental Compliance
Download Datasheet Parametric View All

8N4S272EC-1033CD Overview

LVDS Output Clock Oscillator

8N4S272EC-1033CD Parametric

Parameter NameAttribute value
Is it Rohs certified?conform to
Objectid1308558892
Reach Compliance Codecompliant
Other featuresENABLE/DISABLE FUNCTION; DIFFERENTIAL OUTPUT; TRAY
maximum descent time0.45 ns
Frequency Adjustment - MechanicalNO
frequency stability50%
Installation featuresSURFACE MOUNT
Nominal operating frequency100 MHz
Maximum operating temperature70 °C
Minimum operating temperature
Oscillator typeLVDS
physical size7.0mm x 5.0mm x 1.55mm
longest rise time0.45 ns
Maximum supply voltage3.465 V
Minimum supply voltage3.135 V
Nominal supply voltage3.3 V
surface mountYES
maximum symmetry53/47 %
LVDS Frequency-Programmable
Crystal Oscillator
IDT8N4S272
DATA SHEET
General Description
The IDT8N4S272 is a Factory Frequency-Programmable Crystal
Oscillator with very flexible frequency programming capabilities. The
device uses IDT’s fourth generation FemtoClock
®
NG technology for
an optimum of high clock frequency and low phase noise
performance. The device accepts 2.5V or 3.3V supply and is
packaged in a small, lead-free (RoHS 6) 6-lead ceramic 5mm x 7mm
x 1.55mm package.
The device can be factory programmed to any in the range from
15.476MHz to 866.67MHz and from 975MHz to 1,300MHz and
supports a very high degree of frequency precision of 218Hz or
better. The extended temperature range supports wireless
infrastructure, telecommunication and networking end equipment
requirements.
Features
Fourth generation FemtoClock
®
NG technology
Factory-programmable clock output frequency from 15.476MHz to
866.67MHz and from 975MHz to 1,300MHz
Frequency programming resolution is 218Hz and better
One 2.5V, 3.3V LVDS clock output
Output enable control (positive polarity), LVCMOS/LVTTL
compatible
RMS phase jitter @ 231.25MHz (12kHz - 20MHz):
0.48ps (typical), integer PLL feedback configuration
RMS phase jitter @ 231.25MHz (1kHz - 40MHz):
0.50ps (typical), integer PLL feedback configuration
2.5V or 3.3V supply
-40°C to 85°C ambient operating temperature
Available in a lead-free (RoHS 6) 6-pin ceramic package
Block Diagram
PFD
&
LPF
FemtoClock
®
NG
VCO
1950-2600MHz
Pin Assignment
DNU 1
6 V
DD
5 nQ
4 Q
OSC
f
XTAL
2
÷P
÷N
Q
nQ
nOE 2
GND 3
÷MINT,
MFRAC
25
Configuration Register (ROM)
nOE
Pulldown
7
IDT8N4S272
6-lead ceramic 5mm x 7mm x 1.55mm
package body
CD Package
Top View
IDT8N4S272CCD
REVISION A OCTOBER 3, 2012
1
©2012 Integrated Device Technology, Inc.
HT9170 Dual Tone (DTMF) Receiver
The HT9170 chip is mainly used in the audio field. The following book is to introduce the relevant knowledge in this area....
rain Analog electronics
As an engineer, you should never...
One day, a new engineer asked me, what is the most important thing to do a good product development? This question stumped me. After thinking for a while, I answered: First: Never trust experience, no...
laojiededepan MCU
Orcad learning notes (three) class and sub class in PCB
If you want to draw PCB in orcad, you need to understand the concept of class and subclass. The subclass is a bit like the layer in AD and PADS, but it is not exactly the same. For example: Package Ge...
bigbat PCB Design
I would like to ask about the SPI pin assignment of 2806! Thank you
I want to use the SPI function of 2806, but I only want to use group B SPICLKB, SPISOMIB, SPISETB, and I want to use SPISIMOB as a normal IO port. Is this OK? Thank you all, (first time using DSP)...
xjwbh Microcontroller MCU
[Hua Diao Experience] 17 Beetle ESP32C3 and WS2812 screen music visualization rhythm light
The MAX9814is a low-cost, high-performance microphone amplifier with automatic gain control (AGC) and low-noise microphone bias. The device features a low-noise front-end amplifier, a variable gain am...
eagler8 DIY/Open Source Hardware
How the driver works
After installing the wheel mouse driver on a system that does not support the mouse wheel, rolling the mouse wheel in a program with a scroll bar can cause the scroll bar to scroll. What I want to ask...
qzl1125186 Embedded System

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 1174  1311  740  470  2156  24  27  15  10  44 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号