There may be duplication with the forum, newbie posting.There is some information about capacitive touch.[[i] This post was last edited by Renlairenwang on 2012-5-24 14:59[/i]]...
6. Some issues worth considering in the third phase project and the first and second phase equipment transformation Baosteel's third phase project will gradually start operation, and the transformat...
1. Can the transistor be set to Ib=Ic? 2. Can the collector current of the transistor be set arbitrarily? According to Ic=hfe×Ib, can the collector current be set lower than the above Ic, even if the ...
I am new to circuits. I need to connect a high-frequency amplifier circuit to my FPGA. I would like to ask for recommendations from experts. Or if anyone can make one, that would be fine. The basic re...
Basic way of data packet transmissionBy fxw4511. Introduction cc2500 supports internal hardware data packet processing mechanism, which makes it easier to use wireless protocol programs to transmit da...
[i=s]This post was last edited by kou_1053858502 on 2020-10-19 20:52[/i]AHD/TVI/CVI/CVBS to HDMI/VGA/CVBS Solution Introduction
Solution name: AHD/TVI/CVI/CVBS to HDMI/VGA/CVBS high-definition convers...
Analog engineers have traditionally struggled with complexity when designing power supplies that required multiple outputs, dynamic load sharing, hot-swap, or extensive fault-handling capabilities....[Details]
System design is a complex process. It is not enough to just use ICs. There are many details to consider. This article uses a high-fidelity music playback system as an example to introduce how to s...[Details]
The reason for the light decay of white LEDs: the decline of phosphor performance
So far, the rapid decline of the luminous performance of white light LEDs, especially low-power white light LE...[Details]
I. Introduction
In the field of power conversion, isolated converters (forward, flyback, and double-ended) with low output DC voltage all use MOSFET as the rectifier device. Since these devi...[Details]
Editor's note: In order to help technicians or engineers who have knowledge of PIC microcontroller assembly language quickly master the method of using C language to program PIC microcontrollers, t...[Details]
Traditional
virtual instruments
consist of a data acquisition
board
based on PCI bus and
corresponding software. However, with
the rapid development of
computer
network techno...[Details]
In the "digital pressure measurement" experimental device of applied physics, the subject technical knowledge of analog circuits, digital circuits, sensors and single-chip microcomputers is used. In o...[Details]
People who often surf the Internet until late at night, their families always complain that turning on the big lights in the living room affects their rest, but some people don't have keyboard ligh...[Details]
Current
measurement:
Magnetic balance Hall current
sensor
is used
. The sensor can measure AC from DC to 100kHz.
In automatic measurement and control systems, it is often nec...[Details]
0 Introduction
In the design and construction of communication systems,
communication power supply
is called the heart of the communication system. The power supply system will dire...[Details]
1 Introduction
CAN (Controller Area Network) bus is a kind of field bus. It is used in many industrial sectors due to its outstanding advantages such as high performance, high reliability, high...[Details]
New Automobile
Hydraulic Clutch
The hydraulic control system uses almost 100% advanced engineering plastics, which overcomes the shortcomings of the main and branch cylinders of metal clutc...[Details]
In the development direction of the automotive industry, electric vehicles (EV) and hybrid electric vehicles (HEV) are becoming an obvious trend. From a technical point of view, hybrid power is mor...[Details]
Various electronic and electromagnetic interference inside and outside the car often puts automotive electronic equipment in dangerous working conditions, degrading the performance of electronic eq...[Details]
An intelligent vehicle is a robot that can automatically drive in an environment according to a pre-set mode, or it can autonomously perform specific operations according to the on-site situation. ...[Details]