DIP1999SD028250BD datasheet, PDF

Datasheet> All Categories > Passive components> The resistor> DIP1999SD028250BD

DIP1999SD028250BD: DescriptionArray/Network Resistor, Isolated, 0.2W, 825ohm, 100V, 0.1% +/-Tol, -50,50ppm/Cel, 8025,; CategoryPassive components The resistor; File Size334KB，3 Pages; ManufacturerTT Electronics plc; Websitehttp://www.ttelectronics.com/

Download Datasheet Parametric View All

DIP1999SD028250BD Overview

Array/Network Resistor, Isolated, 0.2W, 825ohm, 100V, 0.1% +/-Tol, -50,50ppm/Cel, 8025,

DIP1999SD028250BD Parametric

Parameter Name	Attribute value
Is it Rohs certified?	incompatible
Objectid	791912192
Reach Compliance Code	compliant
Country Of Origin	USA
ECCN code	EAR99
YTEOL	5.18
structure	Welded
JESD-609 code	e0
Lead length	3.429 mm
lead spacing	2.54 mm
Network Type	Isolated
Number of terminals	16
Maximum operating temperature	150 °C
Minimum operating temperature	-55 °C
Package height	2.032 mm
Package length	20.32 mm
Package form	DIP
Package width	6.35 mm
Rated power dissipation(P)	0.2 W
resistance	825 Ω
Resistor type	ARRAY/NETWORK RESISTOR
series	1900
size code	8025
Temperature Coefficient	50 ppm/°C
Terminal surface	Tin/Lead (Sn60Pb40)
Tolerance	0.1%
Operating Voltage	100 V

DIP1999SD028250BD Preview

TaNFilm Precision DIP Network

Commercial and MIL Qualified

1900 Series

Inherent reliability

MIL-PRF-83401 qualified

Custom configuration available

Bonded leads not susceptible to

solder reflow problems

Absolute tolerance to

±0.1% / ratio tolerance to ±0.05%

Absolute TCR to

±15ppm/°C / ratio tracking to ±5ppm/°C



√

_____

General Note

TT electronics reserves the right to make changes in product specification without notice or liability.

All information is subject to TT electronics’ own data and is considered accurate at time of going to print.

www.bitechnologies.com www.irctt.com www.welwyn-tt.com

09. 11

TaNFilm

Precision DIP Network

Commercial and MIL Qualified

1900 Series

General Note

TT electronics reserves the right to make changes in product specification without notice or liability.

All information is subject to TT electronics’ own data and is considered accurate at time of going to print.

www.bitechnologies.com www.irctt.com www.welwyn-tt.com

09. 11

TaNFilm

Precision DIP Network

Commercial and MIL Qualified

1900 Series

General Note

TT electronics reserves the right to make changes in product specification without notice or liability.

All information is subject to TT electronics’ own data and is considered accurate at time of going to print.

www.bitechnologies.com www.irctt.com www.welwyn-tt.com

09. 11

More (Only the first 5 pages are displayed. Please Download Datasheet to view the full content.) >

Recommended Resources

Fault signal trip circuit

Feedback signal parallel synthesis

Automatic digital meter inverter power supply circuit diagram

LA4558 audio IC amplifier circuit diagram

Gas leak detection alarm

Monolithic Radio Circuit-

Looking for STM32F107 USB HID 64-bit data transmission and reception routine: I am debugging the STM32F107 USB HID routine, and there is a problem that it can only receive but not send. I hope friends who have done this can provide a complete routine for learning. :)...; lzq2804 stm32/stm8

28335Change the output pin level through the GPADAT register?: The GPADAT register is used in the program to change the output pin level: #define GP_EN GpioDataRegs.GPADAT.bit.GPIO2 #define GP_OE GpioDataRegs.GPADAT.bit.GPIO4 #define GP_A GpioDataRegs.GPADAT.bit....; 喜鹊王子 DSP and ARM Processors

Has anyone done WHQL certification?: My NDIS intermediate layer driver needs to be used on 64-bit Windows 7. Does it need to be WHQL certified? How can I obtain this certification?...; lhy705 Embedded System

Questions about using an oscilloscope differential probe to measure the voltage across a resistor and calculate the current: Due to the limited instruments at hand, I plan to use a differential probe to measure the voltage across the resistor as shown in the figure below, so as to calculate the laser current. There are two ...; xiaxingxing Analog electronics

The WinCE device is identified as a USB disk.: Hello everyone. My development platform is S3C2410+WINCE5.0, and I want to make the WINCE device be recognized as a USB disk when it is connected to the PC via a USB cable. I changed the relevant regi...; liplip Embedded System

Allegro software usage: When placing a component in Allegro, it says W- (SPMHUT-48): Scaled value has been rounded off. Why can't the component be placed? I searched online and found that some people said the board frame is ...; 一战到底 PCB Design

Shortcut: E0 E1 E2 E3 E4 E5 E6 E7 E8 E9 EA EB EC ED EE EF EG EH EI EJ EK EL EM EN EO EP EQ ER ES ET EU EV EW EX EY EZ F0 F1 F2 F3 F4 F5 F6 F7 F8 F9 FA FB FC FD FE FF FG FH FI FJ FK FL FM FN FO FP FQ FR FS FT FU FV FW FX FY FZ G0 G1 G2 G3 G4 G5 G6 G7 G8 G9 GA GB GC GD GE GF GG GH GI GJ GK GL GM GN GO GP GQ GR GS GT GU GV GW GX GZ H0 H1 H2 H3 H4 H5 H6 H7 H8 HA HB HC HD HE HF HG HH HI HJ HK HL HM HN HO HP HQ HR HS HT HU HV HW HX HY HZ I1 I2 I3 I4 I5 I6 I7 IA IB IC ID IE IF IG IH II IK IL IM IN IO IP IQ IR IS IT IU IV IW IX J0 J1 J2 J6 J7 JA JB JC JD JE JF JG JH JJ JK JL JM JN JP JQ JR JS JT JV JW JX JZ K0 K1 K2 K3 K4 K5 K6 K7 K8 K9 KA KB KC KD KE KF KG KH KI KJ KK KL KM KN KO KP KQ KR KS KT KU KV KW KX KY KZ

Popular Components