EEWORLDEEWORLDEEWORLD

Part Number

Search

WBC-T0303AS-03-4753-FJ

Description
Array/Network Resistor, Center Tap, Thin Film, 0.25W, 475000ohm, 100V, 1% +/-Tol, -25,25ppm/Cel, 0303,
CategoryPassive components    The resistor   
File Size376KB,3 Pages
ManufacturerTT Electronics plc
Websitehttp://www.ttelectronics.com/
Environmental Compliance
Download Datasheet Parametric View All

WBC-T0303AS-03-4753-FJ Overview

Array/Network Resistor, Center Tap, Thin Film, 0.25W, 475000ohm, 100V, 1% +/-Tol, -25,25ppm/Cel, 0303,

WBC-T0303AS-03-4753-FJ Parametric

Parameter NameAttribute value
Is it Rohs certified?conform to
Objectid802657154
Reach Compliance Codecompliant
ECCN codeEAR99
structureChip
Network TypeCenter Tap
Number of terminals6
Maximum operating temperature150 °C
Minimum operating temperature-55 °C
Package length0.762 mm
Package formSMT
Package width0.762 mm
method of packingTray
Rated power dissipation(P)0.25 W
resistance475000 Ω
Resistor typeARRAY/NETWORK RESISTOR
seriesWBC(TAPPED)
size code0303
technologyTHIN FILM
Temperature Coefficient25 ppm/°C
Tolerance1%
Operating Voltage100 V
Wire Bondable
Chip Resistors
WBC Series
Discrete or tapped schematics
MIL inspection available
High resistor density
IRC Advanced Film Division
IRC’s WBC series wire bondable chip resistors are ideally suited for
the most demanding hybrid application. The WBC combines IRC’s
TaNSil
®
tantalum nitride thin film technology with silicon substrate processing to produce an extremely small
footprint device with the proven stability, reliability and moisture performance of IRC’s TaNSil
®
resistor film.
Available in a wide range of tolerances and temperature coefficients to fit a variety of hybrid circuit applica-
tions. Custom resistance values, sizes and schematics are available on request from the factory.
Physical Data
R0202 - Discrete
(0.508mm ±0.025)
0.020˝ ±0.001
Electrical Data
Absolute Tolerance
Absolute TCR
R
Package Power Rating
(@ 70°C)
Rated Operating Voltage
(not to exceed
P x R )
Operating Temperature
Back contact
Noise
Substrate Material
Top contact
Substrate Thickness
Aluminum
Gold
R0202 and
T0303
B0202
Passivation
to ±0.1%
to ±25ppm/°C
250mW
100V
-55°C to +150°C
<-30dB
Oxidized Silicon
(10KÅ SiO
2
min)
0.010˝ ±0.001
(0.254mm ±0.025)
10KÅ minimum
15KÅ minimum
Silicon
(Gold available)
Gold
3KÅ minimum
Silicon Dioxide or
Silicon Nitride
0.004˝ min bond pad size
0.020˝ ±0.001
(0.508mm ±0.025)
B0202 - Discrete back contact
(0.508mm ±0.025)
0.020˝ ±0.001
R
Top contact
pad chamfered
0.004˝ min bond pad size
0.020˝ ±0.001
(0.508mm ±0.025)
T0303 - Tapped network ½R + ½R
Bond Pad
Metallization
(0.762mm ±0.025)
0.030˝ ±0.001
Backside
½R
½R
0.030˝ ±0.001
(0.762mm ±0.025)
0.004˝ min bond pad size
General Note
IRC reserves the right to make changes in product specification without notice or liability.
All information is subject to IRC’s own data and is considered accurate at time of going to print.
© IRC Advanced Film Division
• Corpus Christi Texas 78411 USA
Telephone: 361 992 7900 • Facsimile: 361 992 3377 • Email: afdsales@irctt.com • Website: www.irctt.com
A subsidiary of
TT electronics plc
WBC Series Issue April 2006
A brief discussion on the “three-dimensional” design of hard waveguide components
By optimizing the varieties and specifications of hard waveguide components commonly used in radar transmission lines and simplifying the design and process documents, the "three modernizations" level...
JasonYoo Embedded System
STC15F2K6S2 completes the communication between the master and the slave stc15w404AS via SPI
I used STC15F2K6S2 to make the host communicate with the slave stc15w404AS through SPI, but the data returned by the slave is blank! I would like to ask for your guidance! [/font][/color] [color=#4444...
jun31 MCU
Is there a picture that introduces the composition and classification of high-frequency switching power supplies?
The key to miniaturization and lightness of electronic devices is the miniaturization of power supply, so it is necessary to reduce the loss in the power supply circuit as much as possible. The adjust...
qwqwqw2088 Power technology
FPGA video display frame synchronization
FPGA video processing, after storing valid data in DDR, how to design the restoration circuit when outputting and displaying? BT.656 format I use TVP5150, and use its AVID and VBLK pins to control the...
jokeboy999 FPGA/CPLD
Software delay: Using different parameters in the for loop will result in a big difference in delay
[color=#000][size=14px][backcolor=rgb(209, 217, 226)][font=Simsun]while(1)[/font][/backcolor][/size][/color] [color=#000][size=14px][backcolor=rgb(209, 217, 226)][font=Simsun]{[/font][/backcolor][/siz...
czx2014 stm32/stm8
Which network components in Platform builder5.0 are related to WIFI?
I want to customize a WINCE5.0 ARMV4I simulator with WIFI function. Which network components should I choose? I bought a wireless network card. How should I configure the simulator so that I can acces...
245016767 Embedded System

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 2055  2211  1212  1251  1924  42  45  25  26  39 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号