Operating Temperature Range -20°C to +70°C or -40°C to +85°C
Tape and Reel Packaging, EIA-418
Wireless Communications
Broadband Access
FPGA/Microcontrollers
Computer Peripherals
Microprocessors
Test and Measurement
Consumer Electronics
Portable Equipment
Part Dimensions:
11.1 × 4.83 × 3.2mm
•
587.84mg
Applications
Description
CTS ATSSMLP incorporates a high Q quartz resonator in a proven resistance-weld metal package. ATSSMLP offers
tight stability options that are ideal for supporting a wide range of commercial and industrial applications.
Ordering Information
Model
LP
Frequency Code
[MHz]
XXX
Mode of
Oscillation
F
Tolerance
@ +25°C
3
Temperature
Stability
3
Temperature
Range
I
Load
Capacitance
D
Packaging
T
Code
Frequency
Product Frequency Code
1
Code
1
X
2
Y
3
Tolerance
±10ppm
±15ppm
±20ppm
±25ppm
±30ppm
Code Temp. Range
-20°C to +70°C
C
-40°C to +85°C
I
Packing
Code
Tape & Reel
T
Code
F
T
Mode
Fundamental
3rd Overtone
Code
1
X
2
Y
3
5
Stability
±10ppm
±15ppm
±20ppm
±25ppm
±30ppm
±50ppm
2
Code Capacitance Code Capacitance
K
D
8pF
18pF
9pF
20pF
J
E
10pF
24pF
A
F
12pF
30pF
L
G
13pF
32pF
B
H
16pF
Series
C
S
Notes:
1] Refer to document 016-1454-0, Frequency Code Tables. 3-digits for frequencies <100MHz.
2] Check factory availability when combined with -40°C to +85°C temperature range.
Not all performance combinations and frequencies may be available.
Contact your local CTS Representative or CTS Customer Service for availability.
This product is specified for use only in standard commercial applications. Supplier disclaims all express and implied warranties and liability in connection with any use of this
product in any non-commercial applications or in any application that may expose the product to conditions that are outside of the tolerances provided in its specification.
Two weeks have passed since the TI MSP430F5529 training [Study with courtesy], and only two netizens on the forum have completed the training and received the development board. The winners of the fir...
To achieve simultaneous digital writing while reading analog data [1] , follow these steps:
1.Use any given entry in a channel gain queue
2.Take the digital data and then mask all unused bits by perfo...
Sunday morning run, first time getting up at 5:00, first time experiencing the morning, first time watching the sun slowly rise, everything needs to be done early. Draw a love heart, full of positive ...
[font=宋体]Test address alignment code on different platforms[/font] [font=宋体] char buf[20];[/font] [font=宋体] long *p;[/font] [font=宋体] [/font] [font=宋体] for (int i = 0; i < 20; i++) {[/font] [font=宋体] ...
I have a dual DSP board with four SPI lines connected directly. After the board is soldered, the two DSPs cannot be JTAG connected at the same time, but they can be connected individually. Please help...
All electronic design engineers and scientists have performed electrical signal analysis, or signal analysis for short. Through this basic measurement, they can gain insight into signal details and...[Details]
When choosing a laptop battery, you should consider several factors, such as power, appearance, and quality.
Regarding power, we often see that a manufacturer uses values such as the number ...[Details]
Battery life is critical for portable applications. For applications such as smoke detectors, security devices, and thermostats, factory-installed batteries need to last for more than 10 years. The...[Details]
With the rapid development of urban economy, elevators are increasingly used as a vertical transportation tool. However, elevator fault detection and maintenance, especially the role of elevator remot...[Details]
From the PIC16F946 datasheet, we know that there are two ways to write values to the LCD for display:
1. Directly write the value to LCDDATA1~LCDDATA23
2. Use disconnect t...[Details]
1. Introduction
At present, most lighting equipment still uses traditional energy for lighting. Making full use of solar energy as the energy supply for lighting equipment is of great si...[Details]
Vertical cavity surface emitting lasers (VCSELs) are gradually replacing traditional edge emitting lasers, especially in low bandwidth and short-distance communication systems where cost factors ar...[Details]
Overview:
This paper introduces a method of connecting a CAN-bus network with Ethernet to form a medium-sized remote monitoring/data transmission network.
CAN (Controller Area Network) is ...[Details]
LED is the abbreviation of light emitting diode, which is an electric light source made of semiconductor technology. The core part of LED is a chip composed of P-type semiconductor and N-type semi...[Details]
Many battery-powered systems require a visual indicator to show when the battery needs to be replaced. LEDs are commonly used for this purpose, but they consume at least 10mA of current. This con...[Details]
It is well known to automotive suppliers that automakers are demanding more from their supply base. For connector suppliers, this means stricter requirements for product performance, stability and ...[Details]
The era of mobile access to the Internet has arrived, and it will rapidly change the business and infrastructure needs of mobile operators under a whole new trend of requirements. We need 4G LTE to...[Details]
With the rapid development of wireless
digital communication
, more challenges have been raised for integrated circuit design and testing. In the product design stage, in order to ensure
t...[Details]
0 Introduction
Ultrasonic waves
are mechanical waves with a frequency of more than 20KHz, and the propagation speed in the air is about 340 m/s (at 20°C). Ultrasonic waves can be gene...[Details]
The launch of Shenzhou IX is imminent, and Tiangong is welcoming visitors again. Yesterday, Professor Fu Qiang, Vice President of the Institute of Science and Industrial Technology of Harbin Instit...[Details]
Microcontroller MCU
京公网安备 11010802033920号
EEWORLD
