If any questions arise whether to use the Rated Ambient Temperature” the Rated Terminal Part Temperature” your usage conditions, please give priority to the Rated Terminal Part Temperature”
“
or “
in
“
.
For more details, please refer to Introduction of the derating curves based on the terminal part temperature” page 14 to 17.
Emission detection methods and technologies The harmful pollutants controlled by automobile emission regulations are mainly the four categories mentioned above. The detection methods recommended by th...
I just graduated and I am currently engaged in UI programming design for embedded software. I have no interest in writing upper-level applications and I have no passion for the job. I like hardware de...
When using PROTEL, I accidentally changed the system font to the initial number. When I want to change it back, I can't see the original key. Please help me! ! !...
Project Name: Simple Kitchen Intelligent System
Functions to be implemented: 1. For temperature acquisition, 18B20 or thermistor can be used, using the AD of LPC1110 to detect indoor and outdoor tempe...
[list] [*][color=#000000]LM3S9B96 has a speed of up to 80MHz (100MMIPS), 256KB of flash memory, 96KB of static memory, and supports 10/100M Ethernet, USB OTG, 3.2 or 4.3-inch touch screen, SD card, I2...
1. Problem When developing STM32 with IAR, I found that I could not print floating point numbers by redirecting printf to the serial port. The code is as follows: The output is as follows: It can...[Details]
In the actual project development process, hardware circuits often need to be modified, and the modified parts need to modify the driver. Thinking about the coming and going of such requirements is t...[Details]
The program got stuck during LCD initialization. Through hardware debugging, it was found that it was stuck in the Delay_ms() function. Going to the definition, it was found to be a macro definition ...[Details]
Serial Port: 一. USART_ITConfig(USART1, USART_IT_TXE, ENABLE): As long as the transmit register is empty, there will always be an interrupt. Therefore, if you are not sending data, turn off the tran...[Details]
Since the first draft of the 5G
NR standard was officially launched at
the end of 2017
, the
5G
commercialization process has taken a substantial step forward. From that moment on, mo...[Details]
In the project, CPLD is needed to complete part of the algorithm design. The parameters are given by AVR, so the communication between AVR and CPLD needs to be completed. Therefore, a test program is...[Details]
What is SYSTICK: This is a 24-bit system tick timer, SysTick, with automatic reload and overflow interrupt functions. All microcontrollers based on the Cortex_M3 processor can obtain a certain time ...[Details]
What are your expectations and ideas
for
the future of
Xiaomi Mi Band
?
Xiaomi Mi Band’s
official Weibo shared many netizens’ thoughts on
the future direction and functions
of Xiao...[Details]
Independent watchdog (IWDG) and low power mode are often used in STM32 development. The watchdog is to detect and solve faults caused by software errors, and the low power mode is to enter sleep mode...[Details]
According to MEMS Consulting, single-chip radar system-on-chip (SoC) is becoming one of the most popular new sensors . Its widespread adoption in automobiles has greatly increased sales, thereby pr...[Details]
When STM32 uses JTMS (PA13) and JTCK (PA14) as normal I/O ports, add the following code before initialization (the order cannot be reversed): RCC_APB2PeriphClockCmd(RCC_APB2Periph_AFIO, ENABLE); G...[Details]
It is required to use MCS-51 microcontroller to sort data. 1. Sort the 8 data in ascending order; 2. The data to be sorted is stored in the internal data memory address units 30H-37H, which are 34H, ...[Details]
Electronics Design Contest
京公网安备 11010802033920号
EEWORLD
