EEWORLDEEWORLDEEWORLD

Part Number

Search

177-740-2-51-2GS4K5-18BAN

Description
Cable Assembly, 24AWG,
CategoryThe connector    Connector bracket   
File Size858KB,5 Pages
ManufacturerGlenair
Websitehttp://www.glenair.com/
Environmental Compliance
Download Datasheet Parametric View All

177-740-2-51-2GS4K5-18BAN Overview

Cable Assembly, 24AWG,

177-740-2-51-2GS4K5-18BAN Parametric

Parameter NameAttribute value
Is it Rohs certified?conform to
Objectid7005056429
Reach Compliance Codecompliant
Country Of OriginUSA
YTEOL8.75
Other featuresSTANDARD: MIL-DTL-83513, EMI SHIELDED
CertificationMIL
Conductor surface treatmentSILVER
conductor materialCOPPER
ConnectorSide1MICRO-D FEMALE
ConnectorSide2MICRO-D FEMALE
Connector bracket typeCABLE ASSEMBLY
structureSTRANDED
Cross-sectional area0.205 mm2
DIN complianceNO
IEC complianceNO
insulator materialPOLYTETRAFLUOROETHYLENE
length0.467 mm
MIL complianceYES
Number of conductors51
Maximum operating temperature150 °C
Minimum operating temperature-55 °C
Rated current3 A
Rated voltage150 V
resistance0.08 Ω
shieldYES
stay19X36
Wire gauge24 AWG
Wire and Cable NamesFLEXIBLE CORD AND FIXTURE WIRE
B
SHIELDING EFFECTIVENESS (Db)
1.00E+04
1.00E+05
1.00E+06
1.00E+07
1.00E+08
1.00E+09
SHIELDING EFFECTIVENESS (Db)
Micro-D Harness
EMI Performance with Ground Spring
100
90
80
70
60
50
40
30
20
10
0
1.00E+03
MWDM Micro-D
Shielded Cable Assembly
Single-Ended or Double-Ended–These
easy-to-order cable
assemblies eliminate the need for expensive assembly labor. 100%
tested and ready for use.
Now With Twisted Pairs–No
need to create a procurement
specification for Micro-D cables with twisted pairs. Glenair 177-740
cables are furnished with a full complement of white/blue twisted
pair wires.
Integral Shield Termination–The
connector shell has a platform
to accept Band-It shield termination bands. The cable shield braid is
attached directly to the connector.
Save Labor, Reduce Weight and Improve EMI Shielding
with Glenair’s Micro-D Shielded Cable Assemblies
Aerospace electronics systems require higher and higher levels of protection from radiated emissions. Glenair’s
fully shielded Micro-D cable assemblies meet this need. The cable shield is attached directly onto the one-
piece connector shell and secured with a stainless steel
Band-Master™ ATS
clamp. These pre-wired, 100% tested
assemblies meet the requirements of MIL-DTL-83513. An optional ground spring on the pin connector assures low
shell-to-shell resistance. Available with a variety of wire types and shields, Micro-D shielded assemblies can be
ordered in any length, either single-ended or “back-to-back”.
Ground Spring and EMI Shielding Effectiveness
A gold-plated stainless steel ground spring on the pin connector mating
face offers substantial improvement in EMI protection. The graphs
compare identical connectors tested with and without ground springs.
EMI Performance without Ground Spring
100
90
80
70
60
50
40
30
20
10
0
1.00E+03
1.00E+04
1.00E+05
1.00E+06
1.00E+07
1.00E+08
1.00E+09
frequency (Hz)
frequency (Hz)
© 2013 Glenair, Inc.
High Performance Micro-D Connectors and Cables
U.S. CAGE Code 06324
Printed in U.S.A.
GLENAIR, INC.
1211 AIR WAY
GLENDALE, CA 91201-2497
818-247-6000
FAX 818-500-9912
www.glenair.com
B-14
E-Mail: sales@glenair.com
ADI Renewable Energy—Solar Photovoltaic Power Generation Solutions
Analog Devices is an industry leader in high-precision signal measurement and control, committed to providing cost-competitive, high-quality ICs for reliable metering, measurement and control....
EEWORLD社区 ADI Reference Circuit
Have you ever used those grating encoders that cost only a few dozen yuan on Taobao? Do you need to process the signal?
This encoder is shown in the figure (100P/R):I tried 2k pull-up and 10k pull-up respectively, and the signals I got were intermittent, and I couldn't tell whether they were positive or negative, they ...
赵怡彬 ST Sensors & Low Power Wireless Technology Forum
The serial port is probably usable, let's show it.
I want to open a serial port on FPGA, but the serial port of de0 is not enough. At first, I thought that the uart in qsys corresponds to the altr uart1.0 in Linux, so I thought that the dts was not wr...
yizhenghuzi FPGA/CPLD
How to modify the font of the comment part in CCS5.4
[align=left][color=#000] It was very easy to change the font of the comment part in CCS3.3. [/color][/align][align=left][color=#000] But I don't know how to change it in CCS5.4. I found that changing ...
darkduck Microcontroller MCU
Summary of the Key Topic Activity---Prepare to make a development board for key learning
In March, we held a discussion on the special activity of keystrokes in the forum ([url=https://bbs.eeworld.com.cn/viewthread.php?tid=97931]https://bbs.eeworld.com.cn/viewthread.php?tid=97931[/url] )....
tiankai001 MCU
Question about the sample-hold/amplifier LF398 zeroing circuit?
As shown in the figure, LF398 always has the problem of not being able to adjust to zero. The online data shows that the power supply voltage is ±15V. The function of R5 is to make the voltage through...
迷途的小书童 Analog electronics

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 1499  2116  2508  2126  1404  31  43  51  29  5 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号