EEWORLDEEWORLDEEWORLD

Part Number

Search

51724-10706810A0

Description
Board Connector, Male, Right Angle, Solder Terminal, Locking
CategoryThe connector    The connector   
File Size267KB,3 Pages
ManufacturerAmphenol
Websitehttp://www.amphenol.com/
Download Datasheet Parametric View All

51724-10706810A0 Overview

Board Connector, Male, Right Angle, Solder Terminal, Locking

51724-10706810A0 Parametric

Parameter NameAttribute value
Is it Rohs certified?incompatible
Objectid308902154
Reach Compliance Codecompliant
ECCN codeEAR99
body width0.574 inch
subject depth0.93 inch
body length6.04 inch
Connector typeBOARD CONNECTOR
Contact to complete cooperationAU ON NI
Contact completed and terminatedTin/Lead (Sn/Pb)
Contact point genderMALE
Contact materialPHOSPHOR BRONZE
Contact resistance20 mΩ
Contact styleHYBRID
Dielectric withstand voltage2500VDC V
Durability200 Cycles
maximum insertion force.973 N
Insulation resistance500000000 Ω
insulator materialGLASS FILLED THERMOPLASTIC
JESD-609 codee0
Manufacturer's serial number51724
Mixed contactsYES
Installation option 1LOCKING
Installation methodRIGHT ANGLE
Installation typeBOARD
Number of connectorsONE
Maximum operating temperature125 °C
Minimum operating temperature-55 °C
Plating thickness30u inch
Rated current (signal)3 A
GuidelineUL
reliabilityCOMMERCIAL
Terminal length0.135 inch
Termination typeSOLDER
Evacuation force-minimum value.17792 N
PDM: Rev:L
STATUS:
Released
Printed: Dec 20, 2010
.
Question about calculating inductance of flyback converter
In these three formulas, Ipk is the peak current, L is the inductance, Lp is the primary inductance of the flyback converter, and f is the switching frequency. I have the following questions: 1. Why d...
warchiefl Analogue and Mixed Signal
In which stolen file is the SfGetObjectName method located?
As the title says, I copied the driver written by others and it went wrong. Does anyone know which header file the SfGetObjectName() method is in?...
shdh6015 Embedded System
Use SAM-BA to connect ARM9 to PC via USB
As the title says, my development board does not have a USB plug, only pins, so when connecting, should the ARM development board be connected as a host or a device? Does anyone know?...
votex威 ARM Technology
About the 8-inch LCD screen backlight driver problem
Dear friends in the forum, I have a question, see the picture:At present, the backlight of this part of the circuit diagram is not very bright, it feels a bit dark, and I don't understand the modulati...
czypf Analog electronics
[Me and WEBENCH] 12V to 5V power supply design based on TPS54229E (physical test)
[i=s] This post was last edited by fengye5340 on 2013-12-24 16:23 [/i] [align=left][b][color=#0070C0][font=宋体][size=14.0pt]【Solution Introduction】[/size][/font][/color][/b][/align][align=left][b][colo...
fengye5340 Analogue and Mixed Signal
Math board routing
I would like to ask you, when routing the digital board, there are four DDR chips, divided into two, I would like to ask you, in the DDR routing, which ones should be of equal length? I have seen a ve...
dandanyuan PCB Design

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 683  2080  1884  428  132  14  42  38  9  3 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号