EEWORLDEEWORLDEEWORLD

Part Number

Search

B0202AA-03-2771-D

Description
Fixed Resistor, Thin Film, 0.25W, 2770ohm, 100V, 0.5% +/-Tol, 25ppm/Cel, Surface Mount, 0202, CHIP
CategoryPassive components    The resistor   
File Size381KB,3 Pages
ManufacturerTT Electronics plc
Websitehttp://www.ttelectronics.com/
Download Datasheet Parametric View All

B0202AA-03-2771-D Overview

Fixed Resistor, Thin Film, 0.25W, 2770ohm, 100V, 0.5% +/-Tol, 25ppm/Cel, Surface Mount, 0202, CHIP

B0202AA-03-2771-D Parametric

Parameter NameAttribute value
Objectid1579352112
package instruction, 0202
Reach Compliance Codecompliant
ECCN codeEAR99
Installation featuresSURFACE MOUNT
Number of terminals2
Maximum operating temperature150 °C
Minimum operating temperature-55 °C
Package shapeRECTANGULAR PACKAGE
method of packingTRAY
Rated power dissipation(P)0.25 W
Rated temperature70 °C
resistance2770 Ω
Resistor typeFIXED RESISTOR
size code0202
surface mountYES
technologyTHIN FILM
Temperature Coefficient25 ppm/°C
Terminal shapeONE SURFACE
Tolerance0.5%
Operating Voltage100 V
Wire Bondable
Chip Resistors
WBC Series
Discrete or tapped schematics
MIL inspection available
High resistor density
IRC’s WBC series wire bondable chip resistors are ideally suited for
the most demanding hybrid application. The WBC combines IRC’s
TaNSil
®
tantalum nitride thin film technology with silicon substrate processing to produce an extremely small
footprint device with the proven stability, reliability and moisture performance of IRC’s TaNSil
®
resistor film.
Available in a wide range of tolerances and temperature coefficients to fit a variety of hybrid circuit applica-
tions. Custom resistance values, sizes and schematics are available on request from the factory.
Physical Data
R0202 - Discrete
(0.508mm ±0.025)
0.020˝ ±0.001
Electrical Data
Absolute Tolerance
Absolute TCR
Package Power Rating
(@ 70°C)
Rated Operating Voltage
(not to exceed P x R )
Operating Temperature
Back contact
Noise
R
Top contact
pad chamfered
0.004˝ min bond pad size
to ±0.1%
to ±25ppm/°C
250mW
100V
-55°C to +150°C
<-30dB
Oxidized Silicon
(10KÅ SiO
2
min)
0.010˝ ±0.001
(0.254mm ±0.025)
10KÅ minimum
15KÅ minimum
Silicon
(Al / Au optional)
3KÅ Au minimum
10KÅ Al minimum
Silicon Dioxide or
Silicon Nitride
R
0.004˝ min bond pad size
0.020˝ ±0.001
(0.508mm ±0.025)
B0202 - Discrete back contact
(0.508mm ±0.025)
0.020˝ ±0.001
Substrate Material
Top contact
Substrate Thickness
Aluminum
Gold
R0202 and
T0303
B0202
0.020˝ ±0.001
(0.508mm ±0.025)
T0303 - Tapped network ½R + ½R
Bond Pad
Metallization
(0.762mm ±0.025)
0.030˝ ±0.001
½R
½R
Backside
0.030˝ ±0.001
(0.762mm ±0.025)
0.004˝ min bond pad size
Passivation
General Note
IRC reserves the right to make changes in product specification without notice or liability.
All information is subject to IRC’s own data and is considered accurate at time of going to print.
© IRC Advanced Film Division
• Corpus Christi Texas 78411 USA
Telephone: 361 992 7900 • Facsimile: 361 992 3377 • Website: www.irctt.com
A subsidiary of
TT electronics plc
WBC Series Issue January 2009 Sheet 1 of 3
stc89c51 drives transistor as switch circuit
I used the IO of stc89c51 to generate a square wave with a high level of 5v, a low level of 0V, and a duty cycle of 1kHZ and 80%, and then connected the IO to a transistor (as shown in the figure) to ...
rainnnn Analog electronics
How should I modify the SDHC driver in the BSP to support multiple SD devices? Please give me some ideas.
The existing BSP only supports one SD card. (Question 1: Generally speaking, the CPU should be able to support multiple SD cards physically, and it should have relevant registers to indicate the numbe...
zlw Embedded System
How to modify the default value of protel99sePCB toolbar?
I am a beginner. When I draw a PCB board, the default values of the tools on the toolbar are all large. How can I make them smaller? Please help!...
Hxon PCB Design
Address bus programming problem
I am now going to write a program for the address bus of arm9 (YC2440) to achieve the function of transmitting data to another board. I wonder if anyone has done it before? Or is there any information...
nankeey Embedded System
XMC4800 Relax ECAT Kit Review 3 - Testing the EtherCAT Slave
[i=s]This post was last edited by tdatd on 2019-1-8 08:23[/i] After setting up the environment and lighting up the LED, we will go straight to our goal - ethercat communication. We will start the test...
tdatd Industrial Control Electronics
If I plan to use the STM32 series of microcontrollers, what tools should I prepare?
I'd like to ask the moderator and all the teachers, if I plan to use the STM32 series of microcontrollers, what tools should I prepare? As for software, I see some people use REALVIEW MDK, but I can't...
zxq180 stm32/stm8

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 2626  2385  1878  2230  47  53  49  38  45  1 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号