EEWORLDEEWORLDEEWORLD

Part Number

Search

TNPW121051R1BETA0H

Description
Fixed Resistor, Thin Film, 0.33W, 51.1ohm, 200V, 0.1% +/-Tol, 25ppm/Cel, Surface Mount, 1210, CHIP
CategoryPassive components    The resistor   
File Size129KB,8 Pages
ManufacturerVishay
Websitehttp://www.vishay.com
Download Datasheet Parametric View All

TNPW121051R1BETA0H Overview

Fixed Resistor, Thin Film, 0.33W, 51.1ohm, 200V, 0.1% +/-Tol, 25ppm/Cel, Surface Mount, 1210, CHIP

TNPW121051R1BETA0H Parametric

Parameter NameAttribute value
Is it Rohs certified?incompatible
Objectid145071462000
package instructionCHIP
Reach Compliance Codeunknown
Country Of OriginGermany
ECCN codeEAR99
YTEOL7.35
Other featuresLASER TRIMMABLE, RATED AC VOLTAGE (V): 200
structureRectangular
JESD-609 codee0
Installation featuresSURFACE MOUNT
Number of terminals2
Maximum operating temperature125 °C
Minimum operating temperature-55 °C
Package height0.6 mm
Package length3.2 mm
Package formSMT
Package width2.45 mm
method of packingTR, CARDBOARD, 7 INCH
Rated power dissipation(P)0.33 W
Rated temperature70 °C
resistance51.1 Ω
Resistor typeFIXED RESISTOR
size code1210
surface mountYES
technologyTHIN FILM
Temperature Coefficient25 ppm/°C
Terminal surfaceTin/Lead (Sn/Pb) - with Nickel (Ni) barrier
Terminal shapeWRAPAROUND
Tolerance0.1%
Operating Voltage200 V
TNPW
www.vishay.com
Vishay
Lead (Pb)-Bearing High Stability Thin Film Chip Resistors
FEATURES
• Metal film layer on high quality ceramic
• SnPb termination plating, Pb content > 6 %
• Excellent overall stability at different environmental
conditions
0.05 % (1000 h rated power at 70 °C)
• Low temperature coefficient and tight tolerances (± 0.1 %;
± 10 ppm/K)
• Single lot date code available
APPLICATIONS
• Military
• Avionics
• Industrial
TNPW High Stability Thin Film Chip Resistors are the perfect
choice for most fields of modern electronics where lead
(Pb)-bearing terminations are mandatory and reliability and
stability are of major concern.
TECHNICAL SPECIFICATIONS
DESCRIPTION
Imperial size
Metric size code
Resistance range
Resistance tolerance
Temperature coefficient
Climatic category (LCT/UCT/days)
Rated dissipation,
P
70 (2)
Operating voltage,
U
max.
AC
RMS
or DC
Permissible film temperature,
F max.
Operating Temperature Range
Thermal resistance
(3)
Insulation voltage:
U
ins
1 min
Continuous
Failure rate: FIT
observed
75 V
75 V
100 V
75 V
200 V
75 V
0.3 x 10
-9
/h
300 V
75 V
300 V
75 V
870 K/W
550 K/W
55/125/56
0.063 W
50 V
TNPW0402
0402
RR1005M
10
to 100 k
TNPW0603
0603
RR1608M
10
to 332 k
TNPW0805
0805
RR2012M
10
to 1 M
± 1 %; ± 0.5 %; ± 0.1 %
± 50 ppm/K; ± 25 ppm/K; ± 15 ppm/K; ± 10 ppm/K
55/125/56
0.1 W
75 V
55/125/56
0.125 W
150 V
155 °C
-55 °C to 125 °C (155 °C)
440 K/W
220 K/W
170 K/W
55/125/56
0.25 W
200 V
55/125/56
0.33 W
200 V
TNPW1206
1206
RR3216M
10
to 2 M
TNPW1210
(1)
1210
RR3225M
10
to 3.01 M
Notes
(1)
The detail specification EN140401-801 does not cover this product size.
(2)
Rated voltage
P
x
R
. The power dissipation on the resistor generates a temperature rise against the local ambient, depending on the heat
flow support of the printed-circuit board (thermal resistance). The rated dissipation applies only if the permitted film temperature is not
exceeded.
(3)
Measuring conditions in accordance with EN 140401-801.
Revision: 24-Jan-14
Document Number: 31006
1
For technical questions, contact:
thinfilmchip@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT
www.vishay.com/doc?91000
Why do I use int to declare variables when using EEPROM, but there are only 255 of them?
Why do I use int to declare variables when using EEPROM, but there are only 255 of them?...
ylf175300 51mcu
Power supply noise interference processing
一般而言,电源杂讯干扰的传播途径可分为下列二大类:??一、普通模式(Normal Mode):简称通模,指的就是二组输入电源线之间的杂讯。这些杂讯大多是由开关动作或者是静态功率转换器等干扰所造成,当这些干扰与正常讯号重叠在一起时,器材元件是无法分辨的,因为正常讯号也是以通模的状态存在。 ??二、共通模式(Common Mode):简称共模,指的是电源与接地之间的杂讯。这部分杂讯的起因多数是因为接地...
songbo Industrial Control Electronics
Principle of LED brightness control by microcontroller MCU
Microcontrollers MCU are usually considered digital devices. By default, their output voltage level is either high or low, not a neutral value. To achieve the requirement of LED brightness control, th...
火辣西米秀 Microcontroller MCU
Can the register secondary latch be latched correctly?
always@(posedge clk or negedge rst_n) begin ......... areg1<=a; areg2<=areg1; .... end assign a=~areg1& areg2;//High level is valid always@(posedge clk or negedge rst_n) begin ........... if(a) .........
1559638992 FPGA/CPLD
TI's BQ2057 charging current is only 200mA. Please give me some advice based on the picture above!
Using a 5V2A adapter, a lithium battery is fully charged to 4.1V, but the charging current is less than 200mA, the charging speed is too slow. See the picture, please improve...
ZHANGXU716 Analogue and Mixed Signal
[Transfer] Common questions in op amp learning
[i=s] This post was last edited by dontium on 2015-1-23 11:31 [/i] [b]1. What is the function of adding a small resistor to the output of the op amp? [/b] Answer: The protection method for short-circu...
模拟IC Analogue and Mixed Signal

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 931  972  1095  34  2386  19  20  23  1  49 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号