EEWORLDEEWORLDEEWORLD

Part Number

Search

B0202GG-02-6983-C

Description
Fixed Resistor, Thin Film, 0.25W, 698000ohm, 100V, 0.25% +/-Tol, 50ppm/Cel, Surface Mount, 0202, CHIP
CategoryPassive components    The resistor   
File Size381KB,3 Pages
ManufacturerTT Electronics plc
Websitehttp://www.ttelectronics.com/
Download Datasheet Parametric View All

B0202GG-02-6983-C Overview

Fixed Resistor, Thin Film, 0.25W, 698000ohm, 100V, 0.25% +/-Tol, 50ppm/Cel, Surface Mount, 0202, CHIP

B0202GG-02-6983-C Parametric

Parameter NameAttribute value
Objectid1579400806
package instructionCHIP
Reach Compliance Codecompliant
ECCN codeEAR99
Installation featuresSURFACE MOUNT
Number of terminals2
Maximum operating temperature150 °C
Minimum operating temperature-55 °C
Package shapeRECTANGULAR PACKAGE
method of packingTRAY
Rated power dissipation(P)0.25 W
Rated temperature70 °C
resistance698000 Ω
Resistor typeFIXED RESISTOR
size code0202
surface mountYES
technologyTHIN FILM
Temperature Coefficient50 ppm/°C
Terminal shapeONE SURFACE
Tolerance0.25%
Operating Voltage100 V
Wire Bondable
Chip Resistors
WBC Series
Discrete or tapped schematics
MIL inspection available
High resistor density
IRC’s WBC series wire bondable chip resistors are ideally suited for
the most demanding hybrid application. The WBC combines IRC’s
TaNSil
®
tantalum nitride thin film technology with silicon substrate processing to produce an extremely small
footprint device with the proven stability, reliability and moisture performance of IRC’s TaNSil
®
resistor film.
Available in a wide range of tolerances and temperature coefficients to fit a variety of hybrid circuit applica-
tions. Custom resistance values, sizes and schematics are available on request from the factory.
Physical Data
R0202 - Discrete
(0.508mm ±0.025)
0.020˝ ±0.001
Electrical Data
Absolute Tolerance
Absolute TCR
Package Power Rating
(@ 70°C)
Rated Operating Voltage
(not to exceed P x R )
Operating Temperature
Back contact
Noise
R
Top contact
pad chamfered
0.004˝ min bond pad size
to ±0.1%
to ±25ppm/°C
250mW
100V
-55°C to +150°C
<-30dB
Oxidized Silicon
(10KÅ SiO
2
min)
0.010˝ ±0.001
(0.254mm ±0.025)
10KÅ minimum
15KÅ minimum
Silicon
(Al / Au optional)
3KÅ Au minimum
10KÅ Al minimum
Silicon Dioxide or
Silicon Nitride
R
0.004˝ min bond pad size
0.020˝ ±0.001
(0.508mm ±0.025)
B0202 - Discrete back contact
(0.508mm ±0.025)
0.020˝ ±0.001
Substrate Material
Top contact
Substrate Thickness
Aluminum
Gold
R0202 and
T0303
B0202
0.020˝ ±0.001
(0.508mm ±0.025)
T0303 - Tapped network ½R + ½R
Bond Pad
Metallization
(0.762mm ±0.025)
0.030˝ ±0.001
½R
½R
Backside
0.030˝ ±0.001
(0.762mm ±0.025)
0.004˝ min bond pad size
Passivation
General Note
IRC reserves the right to make changes in product specification without notice or liability.
All information is subject to IRC’s own data and is considered accurate at time of going to print.
© IRC Advanced Film Division
• Corpus Christi Texas 78411 USA
Telephone: 361 992 7900 • Facsimile: 361 992 3377 • Website: www.irctt.com
A subsidiary of
TT electronics plc
WBC Series Issue January 2009 Sheet 1 of 3
Design of automobile anti-lock braking system based on MC9S12DP256B
PrefaceWith the increase of vehicle speed and road traffic density, the requirements for vehicle driving safety performance are becoming higher and higher. The anti-lock braking system (ABS) of automo...
frozenviolet Automotive Electronics
TIVA C User Experience 4: ADC
#include#include#include #include #include #include #include #include #include "inc/tm4c123gh6pm.h" #include "inc/hw_types.h" #include "inc/hw_memmap.h" #include "driverlib/sysctl.h" #include "driverl...
upc_arm Microcontroller MCU
What should I do if the data received during CAN transmission and reception is too large?
I am working on a CAN library function. Now I have a problem: What if the received data packet is too large and the receiving buffer cannot hold it? The same problem also occurs during the sending pro...
panzhenlkj NXP MCU
【Altera SoC Experience Tour】+ DE1_SOC First Look
As for the introduction of DE1_SOC board, I won't say much. After getting the board, I first installed the USB blaster II driver, serial port driver, etc. according to the tutorial in the training mat...
白丁 FPGA/CPLD
MFC program cannot run under wince6.0???
It can run on the simulator, but not on the board. I moved the MFC dll from Microsoft Visual Studio 8\VC\ce\Dll\armv4i\ to /windows, but it still can't run. What's going on? ?...
langlangzhi Embedded System
Problems with using TI's power module that generates negative voltage
[align=left][color=#000][font=宋体][size=12px]At the beginning of 2013, a new batch of boards for the project were completed and welded, and it was time to start debugging. When testing various voltages...
qwqwqw2088 Analogue and Mixed Signal

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 1697  2454  2590  646  2267  35  50  53  14  46 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号