EEWORLDEEWORLDEEWORLD

Part Number

Search

8N3DV85LC-0108CDI8

Description
IC osc vcxo dual freq 6-clcc
Categorysemiconductor    Analog mixed-signal IC   
File Size169KB,20 Pages
ManufacturerIDT (Integrated Device Technology, Inc.)
Websitehttp://www.idt.com/
Environmental Compliance  
Download Datasheet Parametric View All

8N3DV85LC-0108CDI8 Online Shopping

Suppliers Part Number Price MOQ In stock  
8N3DV85LC-0108CDI8 - - View Buy Now

8N3DV85LC-0108CDI8 Overview

IC osc vcxo dual freq 6-clcc

8N3DV85LC-0108CDI8 Parametric

Parameter NameAttribute value
Datasheets
IDT8N3DV85
FemtoClock®
NG Ordering Guide
PCN Assembly/Origi
Passivation Thickness 12/Sep/2013
Standard Package1,000
CategoryIntegrated Circuits (ICs)
FamilyClock/Timing - Programmable Timers and Oscillators
PackagingTape & Reel (TR)
TypeVCXO
Cou-
Frequency100MHz, 100MHz
Voltage - Supply2.375 V ~ 2.625 V
Current - Supply120mA
Operating Temperature-40°C ~ 85°C
Package / Case6-CLCC
Supplier Device Package6-CLCC (7x5)
Mounting TypeSurface Mou
Other NamesIDT8N3DV85LC-0108CDI8IDT8N3DV85LC-0108CDI8-ND
LVPECL Dual-Frequency
Programmable VCXO
General Description
The IDT8N3DV85 is a LVPECL Dual-Frequency Programmable
VCXO with very flexible frequency and pull-range programming
capabilities. The device uses IDT’s fourth generation FemtoClock
®
NG technology for an optimum of high clock frequency and low
phase noise performance. The device accepts 2.5V or 3.3V supply
and is packaged in a small, lead-free (RoHS 6) 6-lead ceramic 5mm
x 7mm x 1.55mm package.
The device can be factory-programmed to any two frequencies in the
range of 15.476MHz to 866.67MHz and from 975MHz to 1,300MHz
to the very high degree of frequency precision of 218Hz or better.
The output frequency is selected by the FSEL pin. The extended
temperature range supports wireless infrastructure, telecommuni-
cation and networking end equipment requirements.
IDT8N3DV85
DATASHEET
Features
Fourth Generation FemtoClock
®
NG technology
Programmable clock output frequency from 15.476MHz to
866.67MHz and from 975MHz to 1,300MHz
Two factory-programmed output frequencies
VCO frequency programming resolution is 218Hz and better
Factory-programmable VCXO pull range and control voltage
polarity
VCXO pull range programmable from typical ±12.5 to ±787.5ppm
One 2.5V or 3.3V LVPECL clock output
FSEL control input for frequency selection, LVCMOS/LVTTL
compatible
RMS phase jitter @ 622.08MHz (12kHz - 20MHz):0.46ps (typical)
RMS phase jitter @ 622.08MHz (50kHz - 80MHz): 0.47ps (typical)
2.5V or 3.3V supply voltage
-40°C to 85°C ambient operating temperature
Lead-free (RoHS 6) 6-lead ceramic 5mm x 7mm x 1.55mm
package
Block Diagram
OSC
114.285 MHz
2
Pin Assignment
÷P
PFD
&
LPF
FemtoClock
®
NG
VCO
1950-2600MHz
VC
1
2
3
6
5
4
V
CC
nQ
Q
÷N
Q
nQ
FSEL
V
EE
÷MINT,
MFRAC
9
VC
Pulldown
A/D
23
Configuration Register (ROM)
(Frequency, Pull range, Polarity)
7
IDT8N3DV85
6-lead ceramic 5mm x 7mm x 1.55mm
package body
CD Package
Top View
FSEL
IDT8N3DV85CCD REVISION A OCTOBER 30, 2013
1
©2013 Integrated Device Technology, Inc.
Program to implement CAN interface communication of MCP2515 through FPGA
Now I want to connect FPGA with MCP2515 chip to debug CAN interface. Does anyone have relevant program information? Thank you!...
风色碧空 FPGA/CPLD
Download the ZigBee Evaluation Kit
I am a zigbee beginner and recently purchased Zhou Ligong's zigbee evaluation kit. I would like to share the kit information and hope it will be helpful to everyone....
mervyn RF/Wirelessly
Video display issues
Well, I would like to borrow your popularity to ask for advice. How does the YUV data of the video generated by the decoder display on the LCD? Is there any relevant information? I want to intercept a...
zk12081984 Embedded System
FPGA design counter output jump is not synchronized
I designed a 4-bit counter using FPGA. When simulating, the output pins q0, q1, q2, and q3 cannot change at the same time. This causes a transient state between one state and the next. For example, th...
happyxiaoyaozi FPGA/CPLD
MSP430F149AD sampling problem
Now I want to sample the voltage of 0~4, but after power on, I use a multimeter to measure the output voltage of P6 port! 1.8V! Then the voltage I want to measure is 0.4V. After connecting, the data m...
leaflet Microcontroller MCU
I am planning to buy an ixp development board. Could you please recommend one to me? Thank you!
I am planning to buy an ixp development board (to be used as a distributor in a cluster to forward data packets to a single server in the cluster). Can you give me some advice? Thank you!...
xuancai Embedded System

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 2623  1161  567  1491  2028  53  24  12  31  41 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号