EEWORLDEEWORLDEEWORLD

Part Number

Search

8N3SV75LC-0185CDI8

Description
IC osc vcxo 6-clcc
Categorysemiconductor    Analog mixed-signal IC   
File Size270KB,19 Pages
ManufacturerIDT (Integrated Device Technology, Inc.)
Websitehttp://www.idt.com/
Environmental Compliance  
Download Datasheet Parametric View All

8N3SV75LC-0185CDI8 Online Shopping

Suppliers Part Number Price MOQ In stock  
8N3SV75LC-0185CDI8 - - View Buy Now

8N3SV75LC-0185CDI8 Overview

IC osc vcxo 6-clcc

8N3SV75LC-0185CDI8 Parametric

Parameter NameAttribute value
Datasheets
IDT8N3SV75
FemtoClock®
NG Ordering Guide
PCN Assembly/Origi
Passivation Thickness 12/Sep/2013
Standard Package1,000
CategoryIntegrated Circuits (ICs)
FamilyClock/Timing - Programmable Timers and Oscillators
PackagingTape & Reel (TR)
TypeVCXO
Cou-
Frequency*
Voltage - Supply2.375 V ~ 2.625 V
Current - Supply120mA
Operating Temperature-40°C ~ 85°C
Package / Case6-CLCC
Supplier Device Package6-CLCC (7x5)
Mounting TypeSurface Mou
Other NamesIDT8N3SV75LC-0185CDI8IDT8N3SV75LC-0185CDI8-ND
LVPECL Frequency-Programmable VCXO
IDT8N3SV75
DATASHEET
General Description
The IDT8N3SV75 is a LVPECL Frequency-Programmable VCXO
with very flexible frequency and pull-range programming capabilities.
The device uses IDT’s fourth generation FemtoClock
®
NG
technology for an optimum of high clock frequency and low phase
noise performance. The device accepts 2.5V or 3.3V supply and is
packaged in a small, lead-free (RoHS 6) 6-lead ceramic 5mm x 7mm
x 1.55mm package.
The device can be factory-programmed to any frequency in the
range of 15.476MHz to 866.67MHz and from 975MHz to 1,300MHz
to the very high degree of frequency precision of 218Hz or better.
The extended temperature range supports wireless infrastructure,
telecommunication and networking end equipment requirements.
Features
Fourth generation FemtoClock
®
NG technology
Programmable clock output frequency from 15.476MHz to
866.67MHz and from 975MHz to 1,300MHz
Frequency programming resolution is 218Hz and better
Factory-programmable VCXO pull range and control voltage
polarity
Absolute pull range (APR) programmable from typical ±4.5 to
±754.5ppm
One 2.5V/3.3V LVPECL clock output
Output enable control input, LVCMOS/LVTTL compatible
RMS phase jitter @ 156.25MHz (12kHz - 20MHz): 0.5ps (typical),
2.5V or 3.3V supply voltage
-40°C to 85°C ambient operating temperature
Lead-free (RoHS 6) 6-lead ceramic 5mm x 7mm x 1.55mm
package
Block Diagram
Pin Assignment
VC
1
2
3
6
5
4
V
CC
nQ
Q
OE
OSC
114.285 MHz
2
÷P
PFD
&
LPF
FemtoClock® NG
VCO
1950-2600MHz
÷N
Q
nQ
V
EE
÷MINT,
MFRAC
7
VC
A/D
IDT8N3SV75
6-lead ceramic 5mm x 7mm x 1.55mm
package body
CD Package
Top View
7
25
Configuration Register (ROM)
(Frequency, Pull-range, Polarity)
OE
Pullup
IDT8N3SV75CCD REVISION A NOVEMBER 19, 2013
1
©2013 Integrated Device Technology, Inc.
Welcome the moderator "天意无罪" to take office~~
I'm glad that another netizen has joined the EEWorld moderator team~Here is the new moderator information: Username: God is innocent Responsible section: Comprehensive technical exchange Personal intr...
okhxyyo Integrated technical exchanges
Crack of CADSTAR 16
There is too little information about CADSTAR in this world. I don’t know if the crack for CADSTAR 16 has been released. I have been looking for it for a long time. I wonder if any of you experts know...
wulongsheng PCB Design
51 single chip microcomputer drives stepper motor circuit and program
Here is an introduction to the method of using a 51 single-chip microcomputer to drive a stepper motor . The driving voltage of this stepper motor is 12V , and the step angle is 7.5 degrees . A circle...
externboy 51mcu
I need to buy a second-hand 2410 development board for study. Contact QQ: 42281797 Tel: 13554742552
I need to buy a second-hand 2410 development board for study. Contact QQ: 42281797 Tel: 13554742552 Welcome to contact Thank you...
arkin Embedded System
How to burn the program to the LM3S9B96 board?
:Cry: There is a LM Flash Programmer in the CD. But I don't know how to use it. The boards I used to use were all burned with HEX files, but why do I need to use BIN files this time? I'm a complete no...
cdlyz90 Microcontroller MCU
I would like to ask about fft.
[i=s] This post was last edited by dontium on 2015-1-23 13:39 [/i] Hello teachers, I want to use 2812 to make an fft program, but I don’t know how to start. I would like to ask you how to use TI’s own...
CENTURYYUAN Analogue and Mixed Signal

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 463  2796  2699  1952  1481  10  57  55  40  30 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号