EEWORLDEEWORLDEEWORLD

Part Number

Search

8N4Q001LG-0139CDI

Description
IC osc clock QD freq 10clcc
Categorysemiconductor    Analog mixed-signal IC   
File Size163KB,20 Pages
ManufacturerIDT (Integrated Device Technology, Inc.)
Websitehttp://www.idt.com/
Download Datasheet Parametric View All

8N4Q001LG-0139CDI Online Shopping

Suppliers Part Number Price MOQ In stock  
8N4Q001LG-0139CDI - - View Buy Now

8N4Q001LG-0139CDI Overview

IC osc clock QD freq 10clcc

8N4Q001LG-0139CDI Parametric

Parameter NameAttribute value
Datasheets
IDT8N4Q001 Rev G
FemtoClock®
NG Ordering Guide
Standard Package364
CategoryIntegrated Circuits (ICs)
FamilyClock/Timing - Programmable Timers and Oscillators
PackagingTray
TypeClock Oscill
Cou-
Frequency170MHz, 200MHz, 220MHz, 250MHz
Voltage - Supply2.375 V ~ 2.625 V
Current - Supply155mA
Operating Temperature-40°C ~ 85°C
Package / Case10-CLCC
Supplier Device Package10-CLCC (7x5)
Mounting TypeSurface Mou
Other NamesIDT8N4Q001LG-0139CDIIDT8N4Q001LG-0139CDI-ND
Quad-Frequency Programmable XO IDT8N4Q001 REV G
DATA SHEET
General Description
The IDT8N4Q001 is a Quad-Frequency Programmable Clock
Oscillator with very flexible frequency programming capabilities. The
device uses IDT’s fourth generation FemtoClock® NG technology for
an optimum high clock frequency and low phase noise performance.
The device accepts 2.5V or 3.3V supply and is packaged in a small,
lead-free (RoHS 6) 10-lead ceramic 5mm x 7mm x 1.55mm package.
Besides the four default power-up frequencies set by the FSEL0 and
FSEL1 pins, the IDT8N4Q001 can be programmed via the I
2
C
interface to output clock frequencies between 15.476MHz to
866.67MHz and from 975MHz to 1,300MHz to a very high degree of
precision with a frequency step size of 435.9Hz ÷
N
(N is the PLL
output divider). Since the FSEL0 and FSEL1 pins are mapped to four
independent PLL divider registers (P, MINT, MFRAC and N),
reprogramming those registers to other frequencies under control of
FSEL0 and FSEL1 is supported. The extended temperature range
supports wireless infrastructure, telecommunication and networking
end equipment requirements.
Features
Fourth generation FemtoClock® NG technology
Programmable clock output frequency from 15.476MHz to
866.67MHz and from 975MHz to 1,300MHz
Four power-up default frequencies (see part number order
codes), re-programmable by I
2
C
I
2
C programming interface for the output clock frequency and
internal PLL control registers
Frequency programming resolution is 435.9Hz ÷N
One 2.5V, 3.3V LVDS clock output
Two control inputs for the power-up default frequency
LVCMOS/LVTTL compatible control inputs
RMS phase jitter @ 156.25MHz (12kHz - 20MHz): 0.253ps
(typical), integer PLL feedback configuration
RMS phase jitter @ 156.25MHz (1kHz - 40MHz): 0.263ps
(typical), integer PLL feedback configuration
Full 2.5V or 3.3V supply modes
-40°C to 85°C ambient operating temperature
Available in Lead-free (RoHS 6) package
Block Diagram
OSC
f
XTAL
÷MINT,
MFRAC
2
25
FSEL1
FSEL0
SCLK
SDATA
OE
Pulldown
Pulldown
Pullup
Pullup
Pullup
Pin Assignment
÷P
PFD
&
LPF
FemtoClock® NG
VCO
1950-2600MHz
÷N
Q
nQ
DNU 1
OE 2
GND 3
FSEL0 4
FSEL1 5
10 SCLK
9 SDATA
8 V
DD
7 nQ
6 Q
7
Configuration Register (ROM)
(Frequency, APR, Polarity)
I
2
C Control
IDT8N4Q001
10-lead ceramic 5mm x 7mm x 1.55mm
package body
CD Package
Top View
IDT8N4Q001GCD
REVISION A
MARCH 6, 2012
1
©2012 Integrated Device Technology, Inc.
[KW41Z] HALO lightsaber trademark application, create your own lightsaber brand
[align=left][size=5]From April 1, 2017, the trademark application fee has been reduced to 300 yuan/piece. Moreover, you can apply directly on the official website and skip the agency, which also saves...
littleshrimp NXP MCU
DSP receives data and stores it into an array. I am a newbie and would like to ask for advice. . .
I want to store the data sent from the PC into an array. I can only store a number into a variable by using interrupts. The variable will not change when it is sent again. I use a loop in the interrup...
脑仁都疼 DSP and ARM Processors
When programming with JLINK, "NO Cortex-m device found in JTAG chain" appears
[i=s] This post was last edited by wanghlady on 2015-6-2 15:59 [/i] I have tried some methods found on the Internet and restarted the computer and the program, but it still doesn't work. Please help. ...
wanghlady stm32/stm8
What is a Beijing man?
Growing up in Beijing, I am used to having fun every day. If a man is not funny, life will be boring. Beijing men are generous in doing things, not so fussy, and they are okay with anything. When they...
西门 Talking
Tips for selecting inductors in switching power supplies
Selection of inductor in switching power supply   What is an inductor? And its characteristics   Inductors are commonly used components in switching power supplies. Since their current and voltage pha...
Jacktang Energy Infrastructure?
How to make WinC support AMR audio format (Directshow)
As title...
yinwei2005 Embedded System

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 2253  730  2452  224  2363  46  15  50  5  48 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号