EEWORLDEEWORLDEEWORLD

Part Number

Search

8N4Q001LG-1111CDI

Description
IC osc clock QD freq 10clcc
Categorysemiconductor    Analog mixed-signal IC   
File Size163KB,20 Pages
ManufacturerIDT (Integrated Device Technology, Inc.)
Websitehttp://www.idt.com/
Download Datasheet View All

8N4Q001LG-1111CDI Online Shopping

Suppliers Part Number Price MOQ In stock  
8N4Q001LG-1111CDI - - View Buy Now

8N4Q001LG-1111CDI Overview

IC osc clock QD freq 10clcc

Quad-Frequency Programmable XO IDT8N4Q001 REV G
DATA SHEET
General Description
The IDT8N4Q001 is a Quad-Frequency Programmable Clock
Oscillator with very flexible frequency programming capabilities. The
device uses IDT’s fourth generation FemtoClock® NG technology for
an optimum high clock frequency and low phase noise performance.
The device accepts 2.5V or 3.3V supply and is packaged in a small,
lead-free (RoHS 6) 10-lead ceramic 5mm x 7mm x 1.55mm package.
Besides the four default power-up frequencies set by the FSEL0 and
FSEL1 pins, the IDT8N4Q001 can be programmed via the I
2
C
interface to output clock frequencies between 15.476MHz to
866.67MHz and from 975MHz to 1,300MHz to a very high degree of
precision with a frequency step size of 435.9Hz ÷
N
(N is the PLL
output divider). Since the FSEL0 and FSEL1 pins are mapped to four
independent PLL divider registers (P, MINT, MFRAC and N),
reprogramming those registers to other frequencies under control of
FSEL0 and FSEL1 is supported. The extended temperature range
supports wireless infrastructure, telecommunication and networking
end equipment requirements.
Features
Fourth generation FemtoClock® NG technology
Programmable clock output frequency from 15.476MHz to
866.67MHz and from 975MHz to 1,300MHz
Four power-up default frequencies (see part number order
codes), re-programmable by I
2
C
I
2
C programming interface for the output clock frequency and
internal PLL control registers
Frequency programming resolution is 435.9Hz ÷N
One 2.5V, 3.3V LVDS clock output
Two control inputs for the power-up default frequency
LVCMOS/LVTTL compatible control inputs
RMS phase jitter @ 156.25MHz (12kHz - 20MHz): 0.253ps
(typical), integer PLL feedback configuration
RMS phase jitter @ 156.25MHz (1kHz - 40MHz): 0.263ps
(typical), integer PLL feedback configuration
Full 2.5V or 3.3V supply modes
-40°C to 85°C ambient operating temperature
Available in Lead-free (RoHS 6) package
Block Diagram
OSC
f
XTAL
÷MINT,
MFRAC
2
25
FSEL1
FSEL0
SCLK
SDATA
OE
Pulldown
Pulldown
Pullup
Pullup
Pullup
Pin Assignment
÷P
PFD
&
LPF
FemtoClock® NG
VCO
1950-2600MHz
÷N
Q
nQ
DNU 1
OE 2
GND 3
FSEL0 4
FSEL1 5
10 SCLK
9 SDATA
8 V
DD
7 nQ
6 Q
7
Configuration Register (ROM)
(Frequency, APR, Polarity)
I
2
C Control
IDT8N4Q001
10-lead ceramic 5mm x 7mm x 1.55mm
package body
CD Package
Top View
IDT8N4Q001GCD
REVISION A
MARCH 6, 2012
1
©2012 Integrated Device Technology, Inc.
A question about noise
My classmate asked me a question, see the attachment, I don't have a clue about the third and fourth questions, please give me some tips, thank you. Also, for the noise diagram of the first question, ...
chunlikong Analog electronics
[GD32F350 Development Sharing 4] Timer T0 interrupt: external high-speed clock source 8MHz
[align=center][/align] The 8Mhz crystal oscillator X3 and matching capacitors on the development board are not soldered. I soldered an external crystal oscillator myself, and then set the external cry...
Justice_Gao GD32 MCU
【LPC54100】LPC54102 hardware i2c read mpu6050 problem
/** @brief I2CM bus master example using polling mode** @note* Copyright(C) NXP Semiconductors, 2014* All rights reserved.** @par* Software that is described herein is for illustrative purposes only* ...
大秦正声 NXP MCU
How to use 51 MCU to simulate SPI communication with JN5121
The best microcontroller is AT89S52, thank you very much....
wahehe Embedded System
Looking for a DC-DC module with 0-10V adjustable output current.
For 48V5A lamp, step-down type. Input more than 50 volts, the potentiometer adjusts the maximum output current to 5A. Collect 0-10V signal to automatically adjust the current strength, such as: 0V no ...
fymxgx Power technology
Alternative methods to repair remote controls
Although there are many ways to repair the remote control, they all have disadvantages. Wearing copper wire will wear out the conductive line, sticking aluminum foil is easy to fall off, sticking old ...
zero3360 Analog electronics

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 1307  2721  628  588  1972  27  55  13  12  40 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号