177-740-2-69GP6J1-18RVN datasheet, PDF

Datasheet> All Categories > The connector> Connector bracket> 177-740-2-69GP6J1-18RVN

177-740-2-69GP6J1-18RVN: DescriptionCable Assembly, 26AWG,; CategoryThe connector Connector bracket; File Size858KB，5 Pages; ManufacturerGlenair; Websitehttp://www.glenair.com/; Environmental Compliance

Download Datasheet Parametric View All

177-740-2-69GP6J1-18RVN Overview

Cable Assembly, 26AWG,

177-740-2-69GP6J1-18RVN Parametric

Parameter Name	Attribute value
Is it Rohs certified?	conform to
Objectid	7005066832
Reach Compliance Code	compliant
Country Of Origin	USA
YTEOL	8.75
Other features	STANDARD: MIL-DTL-83513, EMI SHIELDED
Certification	MIL
Conductor surface treatment	SILVER
conductor material	COPPER
ConnectorSide1	MICRO-D MALE
ConnectorSide2	MICRO-D MALE
Connector bracket type	CABLE ASSEMBLY
structure	STRANDED
Cross-sectional area	0.129 mm2
DIN compliance	NO
IEC compliance	NO
insulator material	CROSSLINKED ETHYLENE-TETRAFLUOROETHYLENE
length	0.466 mm
MIL compliance	YES
Number of conductors	69
Maximum operating temperature	150 °C
Minimum operating temperature	-55 °C
Rated current	3 A
Rated voltage	150 V
resistance	0.147 Ω
shield	YES
stay	19X38
Wire gauge	26 AWG
Wire and Cable Names	FLEXIBLE CORD AND FIXTURE WIRE

Preview

Download Datasheet

View All

SHIELDING EFFECTIVENESS (Db)

1.00E+04

1.00E+05

1.00E+06

1.00E+07

1.00E+08

1.00E+09

SHIELDING EFFECTIVENESS (Db)

Micro-D Harness

EMI Performance with Ground Spring

100

1.00E+03

MWDM Micro-D

Shielded Cable Assembly

Single-Ended or Double-Ended–These

easy-to-order cable

assemblies eliminate the need for expensive assembly labor. 100%

tested and ready for use.

Now With Twisted Pairs–No

need to create a procurement

specification for Micro-D cables with twisted pairs. Glenair 177-740

cables are furnished with a full complement of white/blue twisted

pair wires.

Integral Shield Termination–The

connector shell has a platform

to accept Band-It shield termination bands. The cable shield braid is

attached directly to the connector.

Save Labor, Reduce Weight and Improve EMI Shielding

with Glenair’s Micro-D Shielded Cable Assemblies

Aerospace electronics systems require higher and higher levels of protection from radiated emissions. Glenair’s

fully shielded Micro-D cable assemblies meet this need. The cable shield is attached directly onto the one-

piece connector shell and secured with a stainless steel

Band-Master™ ATS

clamp. These pre-wired, 100% tested

assemblies meet the requirements of MIL-DTL-83513. An optional ground spring on the pin connector assures low

shell-to-shell resistance. Available with a variety of wire types and shields, Micro-D shielded assemblies can be

ordered in any length, either single-ended or “back-to-back”.

Ground Spring and EMI Shielding Effectiveness

A gold-plated stainless steel ground spring on the pin connector mating

face offers substantial improvement in EMI protection. The graphs

compare identical connectors tested with and without ground springs.

EMI Performance without Ground Spring

100

1.00E+03

1.00E+04

1.00E+05

1.00E+06

1.00E+07

1.00E+08

1.00E+09

frequency (Hz)

High Performance Micro-D Connectors and Cables

U.S. CAGE Code 06324

Printed in U.S.A.

GLENAIR, INC.

•

1211 AIR WAY

•

GLENDALE, CA 91201-2497

•

818-247-6000

•

FAX 818-500-9912

www.glenair.com

B-14

E-Mail: sales@glenair.com

Recommended Resources

LM2574, LM2574HV application circuit diagram

Use time relay to automatically switch Y start control

Using 5G23 regulated power supply

Start control circuit with phase sequence and phase loss protection

Transistor light meter circuit

Neon light drive circuit

CC1101 sending data problem: When debugging the CC1101 sending program, I found that the program can run normally, but the receiving end can't receive data. The status word of the receiving end is the receiving state, but the sta...; macd RF/Wirelessly

Sorry for the low score and difficult question. I will give you more points after you earn them. Please advise: 2.4.20 kernel, reconnect the same USB disk, and it will definitely not be read the second time: The drivers used are: usbcore.o, usb-uhci.o, usb-storage.o. The experiment is as follows: 1. Load these three drivers first, then connect the U disk, and execute "dd if=/devfs/scsi/host0/bus0/target0/...; fpgafuns Embedded System

51 read and write USB disk: /* This program can read the root directory of a FAT16 file system USB flash drive with 180 lines of C code. You can see the file name under the root directory and display the content of the first fil...; njlianjian 51mcu

Delete Post: [i=s] This post was last edited by chenzumaok on 2018-1-19 06:10 [/i] Delete post...; chenzumaok TI Technology Forum

Duty cycle of PWM wave?: Changing the duty cycle of the PWM wave can make the motor rotate, and changing the period of the PWM wave canadjust the speed. If the period is 500, what will be the difference if I change the duty c...; nick35 Microcontroller MCU

Comparison of solutions + TPS40304 Compensation_Calculation: [b]Required: [/b][align=left]Inputvoltage: 10 – 16V;[/align][align=left]OutPutvoltage:3.3 ;[/align][align=left]MaxOutputCurrent:1Amp;[/align][align=left]Ripple: ±5%[/align][b]Step1:[/b] [b]Step2:[/b][...; jasonheeeeee Analogue and Mixed Signal

Shortcut: A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 AA AB AC AD AE AF AG AH AI AJ AK AL AM AN AO AP AQ AR AS AT AU AV AW AX AY AZ B0 B1 B2 B3 B4 B5 B6 B7 B8 B9 BA BB BC BD BE BF BG BH BI BJ BK BL BM BN BO BP BQ BR BS BT BU BV BW BX BY BZ C0 C1 C2 C3 C4 C5 C6 C7 C8 C9 CA CB CC CD CE CF CG CH CI CJ CK CL CM CN CO CP CQ CR CS CT CU CV CW CX CY CZ D0 D1 D2 D3 D4 D5 D6 D7 D8 D9 DA DB DC DD DE DF DG DH DI DJ DK DL DM DN DO DP DQ DR DS DT DU DV DW DX DZ

Popular Components