177-740-5-21CS6J1-18FNN datasheet, PDF

Datasheet> All Categories > The connector> Connector bracket> 177-740-5-21CS6J1-18FNN

177-740-5-21CS6J1-18FNN: DescriptionCable Assembly, 26AWG,; CategoryThe connector Connector bracket; File Size858KB，5 Pages; ManufacturerGlenair; Websitehttp://www.glenair.com/; Environmental Compliance

Download Datasheet Parametric View All

177-740-5-21CS6J1-18FNN Overview

Cable Assembly, 26AWG,

177-740-5-21CS6J1-18FNN Parametric

Parameter Name	Attribute value
Is it Rohs certified?	conform to
Objectid	7005088852
Reach Compliance Code	compliant
Country Of Origin	USA
YTEOL	8.23
Other features	STANDARD: MIL-DTL-83513
Certification	MIL
Conductor surface treatment	SILVER
conductor material	COPPER
ConnectorSide1	MICRO-D MALE
ConnectorSide2	MICRO-D FEMALE
Connector bracket type	CABLE ASSEMBLY
structure	STRANDED
Cross-sectional area	0.129 mm2
DIN compliance	NO
IEC compliance	NO
insulator material	CROSSLINKED ETHYLENE-TETRAFLUOROETHYLENE
length	0.467 mm
MIL compliance	YES
Number of conductors	21
Maximum operating temperature	150 °C
Minimum operating temperature	-55 °C
Rated current	3 A
Rated voltage	150 V
resistance	0.147 Ω
shield	NO
stay	19X38
Wire gauge	26 AWG
Wire and Cable Names	FLEXIBLE CORD AND FIXTURE WIRE

Preview

Download Datasheet

View All

SHIELDING EFFECTIVENESS (Db)

1.00E+04

1.00E+05

1.00E+06

1.00E+07

1.00E+08

1.00E+09

SHIELDING EFFECTIVENESS (Db)

Micro-D Harness

EMI Performance with Ground Spring

100

1.00E+03

MWDM Micro-D

Shielded Cable Assembly

Single-Ended or Double-Ended–These

easy-to-order cable

assemblies eliminate the need for expensive assembly labor. 100%

tested and ready for use.

Now With Twisted Pairs–No

need to create a procurement

specification for Micro-D cables with twisted pairs. Glenair 177-740

cables are furnished with a full complement of white/blue twisted

pair wires.

Integral Shield Termination–The

connector shell has a platform

to accept Band-It shield termination bands. The cable shield braid is

attached directly to the connector.

Save Labor, Reduce Weight and Improve EMI Shielding

with Glenair’s Micro-D Shielded Cable Assemblies

Aerospace electronics systems require higher and higher levels of protection from radiated emissions. Glenair’s

fully shielded Micro-D cable assemblies meet this need. The cable shield is attached directly onto the one-

piece connector shell and secured with a stainless steel

Band-Master™ ATS

clamp. These pre-wired, 100% tested

assemblies meet the requirements of MIL-DTL-83513. An optional ground spring on the pin connector assures low

shell-to-shell resistance. Available with a variety of wire types and shields, Micro-D shielded assemblies can be

ordered in any length, either single-ended or “back-to-back”.

Ground Spring and EMI Shielding Effectiveness

A gold-plated stainless steel ground spring on the pin connector mating

face offers substantial improvement in EMI protection. The graphs

compare identical connectors tested with and without ground springs.

EMI Performance without Ground Spring

100

1.00E+03

1.00E+04

1.00E+05

1.00E+06

1.00E+07

1.00E+08

1.00E+09

frequency (Hz)

High Performance Micro-D Connectors and Cables

U.S. CAGE Code 06324

Printed in U.S.A.

GLENAIR, INC.

•

1211 AIR WAY

•

GLENDALE, CA 91201-2497

•

818-247-6000

•

FAX 818-500-9912

www.glenair.com

B-14

E-Mail: sales@glenair.com

Recommended Resources

Five-digit LED display audio power indication circuit diagram made with FD502

VF-AT series frequency converter power frequency-variable frequency switching circuit

Analog counter circuit diagram

Xihu brand BYD-155C refrigerator circuit

Amplitude Keying (ASK)

Low power consumption 12V power supply circuit diagram

Help, three cobblers together, ask Zhuge: [i=s] This post was last edited by paulhyde on 2014-9-15 09:02 [/i] I have never participated in this event before. I am a newbie and I need help. I don't know where to start. Experienced people, plea...; levelgod Electronics Design Contest

C6748 firmware boot mode setting problem.: OMAPL138 firmware is put into NOR flash. It is known that (boot[7:0] is multiplexed with upp and GPIO7 pins). For example, I set it to 00000010 NOR flash boot. The switch potential of boot mode is nor...; zhuhu DSP and ARM Processors

The problem encountered in project development is urgent. Please help me if you have customized the system with PB5.0. Thank you.: Since the project is developed with adoce components, after downloading the adoce component package from the Internet, I have been using EVC to copy it in for debugging during the development phase. N...; nebulabhm Embedded System

How to choose the right hardware bus for instrument control system: [p=20, null, left][font=Verdana, sans-serif][size=12px][b][color=#000000]Overview[/color][/b][/size][/font][/p][p=20, null, left][font=Verdana, sans-serif][size=12px][color=#000000][backcolor=white]Wh...; wstt Test/Measurement

【Design Tools】Xilinx_FPGA Selection Quick Reference Table: Xilinx_FPGA Selection Quick Reference Table...; 常见泽1 FPGA/CPLD

Those who work in automotive electronics, please come out and shout: It seems that there are very few people working in automotive electronics. The forum is so popular, have all the automotive electronics people hidden themselves? Everyone, come out. Let's see how many...; 柳飘飘 Automotive Electronics

Shortcut: E0 E1 E2 E3 E4 E5 E6 E7 E8 E9 EA EB EC ED EE EF EG EH EI EJ EK EL EM EN EO EP EQ ER ES ET EU EV EW EX EY EZ F0 F1 F2 F3 F4 F5 F6 F7 F8 F9 FA FB FC FD FE FF FG FH FI FJ FK FL FM FN FO FP FQ FR FS FT FU FV FW FX FY FZ G0 G1 G2 G3 G4 G5 G6 G7 G8 G9 GA GB GC GD GE GF GG GH GI GJ GK GL GM GN GO GP GQ GR GS GT GU GV GW GX GZ H0 H1 H2 H3 H4 H5 H6 H7 H8 HA HB HC HD HE HF HG HH HI HJ HK HL HM HN HO HP HQ HR HS HT HU HV HW HX HY HZ I1 I2 I3 I4 I5 I6 I7 IA IB IC ID IE IF IG IH II IK IL IM IN IO IP IQ IR IS IT IU IV IW IX J0 J1 J2 J6 J7 JA JB JC JD JE JF JG JH JJ JK JL JM JN JP JQ JR JS JT JV JW JX JZ K0 K1 K2 K3 K4 K5 K6 K7 K8 K9 KA KB KC KD KE KF KG KH KI KJ KK KL KM KN KO KP KQ KR KS KT KU KV KW KX KY KZ

Popular Components