Features
•
•
•
•
Single Supply for Read and Write: 2.7 to 3.6V (BV), 3.0 to 3.6V (LV)
Fast Read Access Time – 70 ns
Internal Program Control and Timer
Sector Architecture
– One 16-Kbyte Boot Block with Programming Lockout
– Two 8-Kbyte Parameter Blocks
– Two Main Memory Blocks (32K, 64K Bytes)
Fast Erase Cycle Time – 10 Seconds
Byte-by-byte Programming – 30 µs/Byte Typical
Hardware Data Protection
DATA Polling for End of Program Detection
Low Power Dissipation
– 25 mA Active Current
– 50 µA CMOS Standby Current
Typical 10,000 Write Cycles
•
•
•
•
•
•
Description
The AT49BV/LV001(N)(T) is a 3-volt-only in-system reprogrammable Flash memory.
Its 1 megabit of memory is organized as 131,072 words by 8 bits. Manufactured with
Atmel’s advanced nonvolatile CMOS technology, the device offers access times to
70 ns with power dissipation of just 90 mW over the commercial temperature range.
When the device is deselected, the CMOS standby current is less than 50 µA. For the
1-megabit
(128K x 8)
Single 2.7-volt
Battery-Voltage
™
Flash Memory
AT49BV001
AT49LV001
AT49BV001N
AT49LV001N
AT49BV001T
AT49LV001T
AT49BV001NT
AT49LV001NT
Not Recommended
for New Design
Contact
Atmel to discuss
the latest design in trends
and options
Pin Configurations
Pin Name
A0 - A16
CE
OE
WE
RESET
I/O0 - I/O7
DC
NC
Function
Addresses
Chip Enable
Output Enable
Write Enable
RESET
Data Inputs/Outputs
Don’t Connect
No Connect
DIP Top View
*RESET
A16
A15
A12
A7
A6
A5
A4
A3
A2
A1
A0
I/O0
I/O1
I/O2
GND
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
32
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
VCC
WE
NC
A14
A13
A8
A9
A11
OE
A10
CE
I/O7
I/O6
I/O5
I/O4
I/O3
PLCC Top View
A12
A15
A16
RESET*
VCC
WE
NC
VSOP Top View (8 x 14mm) or
TSOP Top View (8 x 20mm) – Type 1
A11
A9
A8
A13
A14
NC
WE
VCC
*RESET
A16
A15
A12
A7
A6
A5
A4
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
32
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
OE
A10
CE
I/O7
I/O6
I/O5
I/O4
I/O3
GND
I/O2
I/O1
I/O0
A0
A1
A2
A3
I/O1
I/O2
GND
I/O3
I/O4
I/O5
I/O6
14
15
16
17
18
19
20
A7
A6
A5
A4
A3
A2
A1
A0
I/O0
5
6
7
8
9
10
11
12
13
4
3
2
1
32
31
30
29
28
27
26
25
24
23
22
21
A14
A13
A8
A9
A11
OE
A10
CE
I/O7
1110C–FLASH–9/03
Note:
*This pin is a DC on the AT49BV001N(T) and AT49LV001N(T).
AT49BV/LV001N(T) pin 1 for the DIP and PLCC packages and pin 9 for the TSOP package are
don’t connect pins.
To allow for simple in-system reprogrammability, the AT49BV/LV001(N)(T) does not require
high input voltages for programming. Three-volt-only commands determine the read and pro-
gramming operation of the device. Reading data out of the device is similar to reading from an
EPROM; it has standard CE, OE, and WE inputs to avoid bus contention. Reprogramming the
AT49BV/LV001(N)(T) is performed by erasing a block of data and then programming on a
byte-by-byte basis. The byte programming time is a fast 50 µs. The end of a program cycle
can be optionally detected by the DATA polling feature. Once the end of a byte program cycle
has been detected, a new access for a read or program can begin. The typical number of pro-
gram and erase cycles is in excess of 10,000 cycles.
The device is erased by executing the erase command sequence; the device internally con-
trols the erase operations. There are two 8-Kbyte parameter block sections and two main
memory blocks.
The device has the capability to protect the data in the boot block; this feature is enabled by a
command sequence. The 16-Kbyte boot block section includes a reprogramming lock out fea-
ture to provide data integrity. The boot sector is designed to contain user secure code, and
when the feature is enabled, the boot sector is protected from being reprogrammed.
In the AT49BV/LV001N(T), once the boot block programming lockout feature is enabled, the
contents of the boot block are permanent and cannot be changed. In the AT49BV/LV001(T),
once the boot block programming lockout feature is enabled, the contents of the boot block
cannot be changed with input voltage levels of 5.5 volts or less.
Block Diagram
AT49BV/LV001(N)
DATA INPUTS/OUTPUTS
I/O7 - I/O0
VCC
GND
OE
WE
CE
RESET
8
INPUT/OUTPUT
BUFFERS
PROGRAM
DATA LATCHES
Y-GATING
1FFFF
X DECODER
MAIN MEMORY
BLOCK 2
(64K BYTES)
MAIN MEMORY
BLOCK 1
(32K BYTES)
PARAMETER
BLOCK 2
(8K BYTES)
PARAMETER
BLOCK 1
(8K BYTES)
BOOT BLOCK
(16K BYTES)
BOOT BLOCK
(16K BYTES)
10000
0FFFF
PARAMETER
BLOCK 1
(8K BYTES)
PARAMETER
BLOCK 2
(8K BYTES)
MAIN MEMORY
BLOCK 1
(32K BYTES)
MAIN MEMORY
BLOCK 2
(64K BYTES)
AT49BV/LV001(N)T
DATA INPUTS/OUTPUTS
I/O7 - I/O0
8
INPUT/OUTPUT
BUFFERS
PROGRAM
DATA LATCHES
Y-GATING
1FFFF
1C000
1BFFF
CONTROL
LOGIC
Y DECODER
ADDRESS
INPUTS
08000
07FFF
1A000
19FFF
06000
05FFF
18000
17FFF
04000
03FFF
00000
10000
0FFFF
00000
2
AT49BV/LV001(N)(T)
1110C–FLASH–9/03
AT49BV/LV001(N)(T)
Device
Operation
READ:
The AT49BV/LV001(N)(T) is accessed like an EPROM. When CE and OE are low and
WE is high, the data stored at the memory location determined by the address pins is asserted
on the outputs. The outputs are put in the high impedance state whenever CE or OE is high.
This dual-line control gives designers flexibility in preventing bus contention.
COMMAND SEQUENCES:
When the device is first powered on it will be reset to the read or
standby mode depending upon the state of the control line inputs. In order to perform other
device functions, a series of command sequences are entered into the device. The command
sequences are shown in the Command Definitions table. The command sequences are written
by applying a low pulse on the WE or CE input with CE or WE low (respectively) and OE high.
The address is latched on the falling edge of CE or WE, whichever occurs last. The data is
latched by the first rising edge of CE or WE. Standard microprocessor write timings are used.
The address locations used in the command sequences are not affected by entering the com-
mand sequences.
RESET:
A RESET input pin is provided to ease some system applications. When RESET is at
a logic high level, the device is in its standard operating mode. A low level on the RESET input
halts the present device operation and puts the outputs of the device in a high impedance
state. If the RESET pin makes a high-to-low transition during a program or erase operation,
the operation may not be successfully completed and the operation will have to be repeated
after a high level is applied to the RESET pin. When a high level is reasserted on the RESET
pin, the device returns to the read or standby mode, depending upon the state of the control
inputs. By applying a 12V ± 0.5V input signal to the RESET pin, the boot block array can be
reprogrammed even if the boot block lockout feature has been enabled (see Boot Block Pro-
gramming Lockout Override section). The RESET feature is not available on the
AT49BV/LV001N(T).
ERASURE:
Before a byte can be reprogrammed, the main memory block or parameter block
which contains the byte must be erased. The erased state of the memory bits is a logical “1”.
The entire device can be erased at one time by using a 6-byte software code. The software
chip erase code consists of 6-byte load commands to specific address locations with a specific
data pattern (please refer to the Chip Erase Cycle Waveforms).
After the software chip erase has been initiated, the device will internally time the erase opera-
tion so that no external clocks are required. The maximum time needed to erase the whole
chip is t
EC
. If the boot block lockout feature has been enabled, the data in the boot sector will
not be erased.
CHIP ERASE:
If the boot block lockout has been enabled, the Chip Erase function will erase
Parameter Block 1, Parameter Block 2, Main Memory Block 1, and Main Memory Block 2 but
not the boot block. If the Boot Block Lockout has not been enabled, the Chip Erase function
will erase the entire chip. After the full chip erase the device will return back to read mode. Any
command during chip erase will be ignored.
3
1110C–FLASH–9/03
SECTOR ERASE:
As an alternative to a full chip erase, the device is organized into sectors
that can be individually erased. There are two 8-Kbyte parameter block sections and two main
memory blocks. The 8-Kbyte parameter block sections can be independently erased and
reprogrammed. The two main memory sections are designed to be used as alternative mem-
ory sectors. That is, whenever one of the blocks has been erased and reprogrammed, the
other block should be erased and reprogrammed before the first block is again erased. The
Sector Erase command is a six bus cycle operation. The sector address is latched on the fall-
ing WE edge of the sixth cycle while the 30H data input command is latched at the rising edge
of WE. The sector erase starts after the rising edge of WE of the sixth cycle. The erase opera-
tion is internally controlled; it will automatically time to completion.
BYTE PROGRAMMING:
Once the memory array is erased, the device is programmed (to a
logical “0”) on a byte-by-byte basis. Please note that a data “0” cannot be programmed back to
a “1”; only erase operations can convert “0”s to “1”s. Programming is accomplished via the
internal device command register and is a 4-bus cycle operation (please refer to the Com-
mand Definitions table). The device will automatically generate the required internal program
pulses.
The program cycle has addresses latched on the falling edge of WE or CE, whichever occurs
last, and the data latched on the rising edge of WE or CE, whichever occurs first. Program-
ming is completed after the specified t
BP
cycle time. The DATA polling feature may also be
used to indicate the end of a program cycle.
BOOT BLOCK PROGRAMMING LOCKOUT:
The device has one designated block that has
a programming lockout feature. This feature prevents programming of data in the designated
block once the feature has been enabled. The size of the block is 16K bytes. This block,
referred to as the boot block, can contain secure code that is used to bring up the system.
Enabling the lockout feature will allow the boot code to stay in the device while data in the rest
of the device is updated. This feature does not have to be activated; the boot block’s usage as
a write protected region is optional to the user. The address range of the boot block is 00000
to 03FFF for the AT49BV/LV001(N) while the address range of the boot block is 1C000 to
1FFFF for the AT49BV/LV001(N)T.
Once the feature is enabled, the data in the boot block can no longer be erased or pro-
grammed with input voltage level of 5.5V or less. Data in the main memory block can still be
changed through the regular programming method. To activate the lockout feature, a series of
six program commands to specific addresses with specific data must be performed. Please
refer to the Command Definitions table.
BOOT BLOCK LOCKOUT DETECTION:
A software method is available to determine if pro-
gramming of the boot block section is locked out. When the device is in the software product
identification mode (see Software Product Identification Entry and Exit sections) a read from
address location 00002H will show if programming the boot block is locked out for the
AT49BV/LV001(N) and a read from address 1C002H will show if programming the boot block
is locked out for the AT49BV/LV001(N)T. If the data on I/O0 is low, the boot block can be pro-
grammed; if the data on I/O0 is high, the program lockout feature has been activated and the
block cannot be programmed. The software product identification code should be used to
return to standard operation.
4
AT49BV/LV001(N)(T)
1110C–FLASH–9/03
AT49BV/LV001(N)(T)
BOOT BLOCK PROGRAMMING LOCKOUT OVERRIDE:
The user can override the boot
block programming lockout by taking the RESET pin to 12 volts during the entire chip erase,
sector erase or byte programming operation. When the RESET pin is brought back to TTL lev-
els the boot block programming lockout feature is again active. This feature is not available on
the AT49BV/LV001N(T).
PRODUCT IDENTIFICATION:
The product identification mode identifies the device and man-
ufacturer as Atmel. It may be accessed by hardware or software operation. The hardware
operation mode can be used by an external programmer to identify the correct programming
algorithm for the Atmel product.
For details, see Operating Modes (for hardware operation) or Software Product Identification.
The manufacturer and device code is the same for both modes.
DATA POLLING:
The AT49BV/LV001(N)(T) features DATA polling to indicate the end of a
program cycle. During a program cycle an attempted read of the last byte loaded will result in
the complement of the loaded data on I/O7. Once the program cycle has been completed, true
data is valid on all outputs and the next cycle may begin. DATA polling may begin at any time
during the program cycle.
TOGGLE BIT:
In addition to DATA polling the AT49BV/LV001(N)(T) provides another method
for determining the end of a program or erase cycle. During a program or erase operation,
successive attempts to read data from the device will result in I/O6 toggling between one and
zero. Once the program cycle has completed, I/O6 will stop toggling and valid data will be
read. Examining the toggle bit may begin at any time during a program cycle.
HARDWARE DATA PROTECTION:
Hardware features protect against inadvertent programs
to the AT49BV/LV001(N)(T) in the following ways: (a) V
CC
sense: if V
CC
is below 1.8V (typical),
the program function is inhibited. (b) Program inhibit: holding any one of OE low, CE high or
WE high inhibits program cycles. (c) Noise filter: pulses of less than 15 ns (typical) on the WE
or CE inputs will not initiate a program cycle.
5
1110C–FLASH–9/03
51mcu
京公网安备 11010802033920号
EEWORLD
