EEWORLDEEWORLDEEWORLD

Part Number

Search
 PDF

P2010H1214DNTF

Description
Fixed Resistor, Thin Film, 1W, 1210000ohm, 300V, 0.5% +/-Tol, 50ppm/Cel, Surface Mount, 2010, CHIP
CategoryPassive components    The resistor   
File Size143KB,10 Pages
ManufacturerVishay
Websitehttp://www.vishay.com
Environmental Compliance
Download Datasheet Parametric View All

P2010H1214DNTF Overview

Fixed Resistor, Thin Film, 1W, 1210000ohm, 300V, 0.5% +/-Tol, 50ppm/Cel, Surface Mount, 2010, CHIP

P2010H1214DNTF Parametric

Parameter NameAttribute value
Is it Rohs certified?conform to
Objectid284895989
package instructionCHIP
Reach Compliance Codecompliant
Country Of OriginFrance
ECCN codeEAR99
YTEOL7.12
Other featuresANTI-SULFUR, HIGH PRECISION
structureRectangular
Installation featuresSURFACE MOUNT
Number of terminals2
Maximum operating temperature155 °C
Minimum operating temperature-55 °C
Package height0.5 mm
Package length5.08 mm
Package formSMT
Package width2.54 mm
method of packingTR, PLASTIC
Rated power dissipation(P)1 W
Rated temperature70 °C
resistance1210000 Ω
Resistor typeFIXED RESISTOR
size code2010
surface mountYES
technologyTHIN FILM
Temperature Coefficient50 ppm/°C
Terminal surfaceTIN SILVER OVER NICKEL
Terminal shapeWRAPAROUND
Tolerance0.5%
Operating Voltage300 V
Under 6410, I used IROM_Fusing_Tool.exe to make an SD card boot disk and burned something into it, but why did the SD card capacity not change? Is it hidden?
Under 6410, I used IROM_Fusing_Tool.exe to make an SD card boot disk and burned something into it, but why did the SD card capacity not change? Is it hidden?...
htjsmhj Embedded System
DFM should not be limited to chips, PCB needs it more
We all know that even if the silicon is 100% perfect, if any one component of the chip-to-chip communication link (such as the package, connector or circuit board) is damaged, the target system may st...
clj2004000 PCB Design
Report Forum
I've been busy making an amplifier recently, so I don't have time to share my experience with M3 with you. The information is not very valuable (I think the most valuable ones have been posted), and I...
heavenji Microcontroller MCU
Introduction to Intel Embedded Systems Invitational Competition
[i=s]This post was last edited by paulhyde on 2014-9-15 09:01[/i] The "Intel Cup Undergraduate Electronic Design Competition - Embedded System Special Invitational Competition" is part of the National...
open82977352 Electronics Design Contest
Adjustment of basic idle speed of electronically controlled vehicles 3
(2006-04-04 13:20:26 ) e. Turn off the engine after adjusting the basic idle speed, and then clear the fault code (35#) stored in the computer after disconnecting the ISCV circuit. Methods for clearin...
frozenviolet Automotive Electronics
What is the principle of transformer leakage inductance? Why do we need to short-circuit the secondary coil of the transformer when testing leakage inductance?
[size=4] When we use a bridge to test the leakage inductance of a transformer, we need to short-circuit the secondary side, and the inductance obtained by testing the primary side is the leakage induc...
qwqwqw2088 Analogue and Mixed Signal

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 515  1883  2843  2903  156  11  38  58  59  4 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号