EEWORLDEEWORLDEEWORLD

Part Number

Search

SFP9530ABMGNKWS

Description
Fixed Resistor, Thin Film, 0.25W, 953ohm, 100V, 0.1% +/-Tol, -250,250ppm/Cel, 0202,
CategoryPassive components    The resistor   
File Size85KB,3 Pages
ManufacturerVishay
Websitehttp://www.vishay.com
Download Datasheet Parametric View All

SFP9530ABMGNKWS Overview

Fixed Resistor, Thin Film, 0.25W, 953ohm, 100V, 0.1% +/-Tol, -250,250ppm/Cel, 0202,

SFP9530ABMGNKWS Parametric

Parameter NameAttribute value
Objectid992846700
Reach Compliance Codeunknown
Country Of OriginUSA
ECCN codeEAR99
YTEOL7.8
structureChip
Number of terminals2
Maximum operating temperature125 °C
Minimum operating temperature-55 °C
Package height0.254 mm
Package length0.558 mm
Package formSMT
Package width0.558 mm
method of packingWaffle Pack
Rated power dissipation(P)0.25 W
resistance953 Ω
Resistor typeFIXED RESISTOR
seriesSFP
size code0202
technologyTHIN FILM
Temperature Coefficient250 ppm/°C
Tolerance0.1%
Operating Voltage100 V
SFP
www.vishay.com
Vishay Electro-Films
Thin Film Top-Contact Resistor with Part Mark
FEATURES
• Wire bondable
• Part marked - 5 digits
• Small size: 0.022 inches square
• Case: 0202
• Resistance range: 1
to 1 M
Product may not be to scale
The SFP series single-value resistor chips offer a small size,
wide ohmic value range and excellent power capacity.
The SFPs are part marked with resistance value allowing
user the ability to visually determine the resistance value of
the chip.
The SFPs are manufactured using Vishay Electro-Films (EFI)
sophisticated thin film equipment and manufacturing
technology.
The SFPs are 100 % electrically tested and visually
inspected to MIL-STD-883, method 2032 class H or K.
• DC power rating: 250 mW
• Oxidized silicon substrate for good power dissipation
• Resistor material: Tantalum nitride, self passivating
• Moisture resistant
APPLICATIONS
Vishay EFI SFP small resistor chips are widely used in hybrid
packages where space is limited and chip value marking is
important for identification. The die is part marked with the
resistance value. Wire bonding is made to the two pads on
the top of the chip.
TEMPERATURE COEFFICIENT OF RESISTANCE, VALUES, AND TOLERANCES
PARAMETER
Total Resistance Range
Standard Tolerances
TCR
VALUE
1 to 1M
± 0.1, ± 0.5, ± 1
± 25, ± 50, ± 100, ± 250
Tightest Standard Tolerance Available
1%
0.5 %
0.1 %
± 25 ppm/°C
± 50 ppm/°C
± 100 ppm/°C
± 250 ppm/°C
UNIT
%
ppm/°C
1
Ω
10
Ω
30
Ω
100
Ω
200 k
Ω
430 k
Ω
620 k
Ω
1 M
Ω
STANDARD ELECTRICAL SPECIFICATIONS
PARAMETER
Noise, MIL-STD-202, Method 308
100
- 250 k
< 100
or > 251 k
Moisture Resistance, MIL-STD-202, Method 106
Stability, 1000 h, + 125 °C, 125 mW
Operating Temperature Range
Thermal Shock, MIL-STD-202, Method 107, Test Condition F
High Temperature Exposure, + 150 °C, 100 h
Dielectric Voltage Breakdown
Insulation Resistance
Operating Voltage
DC Power Rating at + 70 °C (Derated to zero at + 175 °C)
5 x Rated Power Short-Time Overload, + 25 °C, 5 s
Note
• Values above 1M available
Revision: 15-Aug-11
1
For technical questions, contact:
efi@vishay.com
VALUE
- 35 typ.
- 20 typ.
± 0.5 max.
R/R
± 0.25 max.
R/R
- 55 to + 125
± 0.25 max.
R/R
± 0.5 max.
R/R
200
10
12
min.
100 V max.
0.250
± 0.25 max.
R/R
UNIT
dB
%
%
°C
%
%
V
V
W
%
Document Number: 61000
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT
www.vishay.com/doc?91000
CC2530 Download Board/Base
The project requires that the program cannot be downloaded on the product board, so it must be downloaded before welding. Therefore, I am looking for a CC2530/pin40 base. I would like to ask for advic...
DILIDILI RF/Wirelessly
About btfss and btfsc instructions
As shown in the figure, why the program can only display one number and not two numbers alternately....
windirection Microchip MCU
The clock clk is generated by the input a and b AND gate. How to program it as the clock signal of the D flip-flop in VHDL?
The clock clk is generated by the AND gate of input quantities a and b. How to program it as the clock signal of the D flip-flop in VHDL? It seems that clk cannot be defined as a variable or signal ty...
wuweiliang FPGA/CPLD
Rail pressure sensor
Have you ever made this product? Please share your experience....
zhaochong110 Sensor
0805 package size / 0402 package size / 0603 package size / 1206 package size
Package size and power relationship:   0201 1/20W   0402 1/16W   0603 1/10W   0805 1/8W   1206 1/4W Package size and package correspondence0402=1.0mmx0.5mm   0603=1.6mmx0.8mm   0805=2.0mmx1.2mm   1206...
笑溜溜 PCB Design

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 2548  2901  1868  1650  769  52  59  38  34  16 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号