EEWORLDEEWORLDEEWORLD

Part Number

Search

51760-11914009BALF

Description
Board Connector, Female, Right Angle, Solder Terminal, Guide Pin, Receptacle
CategoryThe connector    The connector   
File Size259KB,3 Pages
ManufacturerAmphenol
Websitehttp://www.amphenol.com/
Environmental Compliance
Download Datasheet Parametric View All

51760-11914009BALF Overview

Board Connector, Female, Right Angle, Solder Terminal, Guide Pin, Receptacle

51760-11914009BALF Parametric

Parameter NameAttribute value
Is it Rohs certified?conform to
Objectid307948270
Reach Compliance Codecompliant
ECCN codeEAR99
Board mount optionsHOLE .086-.098
body width0.47 inch
subject depth0.82 inch
Body/casing typeRECEPTACLE
Connector typeBOARD CONNECTOR
Contact completed and terminatedTIN
Contact point genderFEMALE
Contact materialCOPPER ALLOY
Contact resistance20 mΩ
Contact styleHYBRID
Dielectric withstand voltage2500VDC V
Durability200 Cycles
maximum insertion force.973 N
Insulation resistance500000000 Ω
insulator materialGLASS FILLED POLYETHYLENE
Manufacturer's serial number51760
Mixed contactsYES
Installation option 1GUIDE PIN
Installation option 2LOCKING
Installation methodRIGHT ANGLE
Installation typeBOARD
Number of connectorsONE
Maximum operating temperature105 °C
Minimum operating temperature-55 °C
Rated current (signal)3 A
GuidelineUL
reliabilityCOMMERCIAL
Terminal length0.09 inch
Termination typeSOLDER
Evacuation force-minimum value.17792 N
PDM: Rev:M
STATUS:
Released
Printed: Dec 20, 2010
.
ADuCM360 interrupt problem,
After ADuCM360 enters interrupt, the manual does not explain how to clear the interrupt again. I thought it would be cleared after entering interrupt, but when debugging, I found that after entering i...
dontium ADI Reference Circuit
How to start Wince system without BOOTLOADER?
Usually when we load the wince system, we always compile the eboot and then download it to the flash, and then download NK according to the menu prompts. In actual products, BOOTLOADER is not needed, ...
xioajinglchy Embedded System
Siemens s7200 programming problem
Why can't Q0.2 be turned on when M1.0 becomes 1, but Q0.2 is turned on when M1.1 becomes 1?...
eeleader Industrial Control Electronics
Make a timer with C51
Give me the following program to add a pause and clear function //Main program #includesbit ksec=P3^0; sbit kmin=P3^1; sbit khour=P3^2; unsigned char secshi=0,secge=0,minshi=0,minge=0,hourshi=0,hourge...
jianghan 51mcu
DAC8552 chip pin problem?
SPI (SYNC, MOSI, MISO, SCK) has these 4 wires. I checked a lot of information on the Internet. Generally, chips that use SPI have these 4 wires, which means that the chip can be read or written. But r...
猎狐梦痕 Analogue and Mixed Signal
A small question about 5509gpio, thank you everyone
1. For example, the iodir address of gpio in the manual is 0x3400, and the address of iodata is 0x3401. Now if I need to output a 1 to gpio6, assuming that gpio6 has been set to output state, can I ju...
ganweixu DSP and ARM Processors

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 1590  2001  2725  850  1965  33  41  55  18  40 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号