Hello everyone, I have a question for you about how to use the PCB footprint in the integrated library in Altium Designer. After adding the device integrated library and the connect integrated library...
[i=s]This post was last edited by 莀荒蔚 on 2020-3-29 12:37[/i]Protocol stack version 1.3.0, slave file1.Add call to DHT11 acquisition event (SBP_START_DEVICE_EVT event in SimpleBLEPeripheral_ProcessEven...
Hot ground: The switching power supply does not need to use a transformer. The "ground" of its switching circuit is related to the mains power grid, the so-called "hot ground", which is a cold ground ...
[i=s]This post was last edited by dontium on 2015-1-23 11:43[/i]This post mainly reviews the use of integrated operational amplifiers in circuits, that is, integrated operational amplifier circuits. T...
I wrote a small program and combined it with VxWorks in Tornado. The program is very simple, just reading the memory! xd0 = *(unsigned int *)(SDRAM_ADR); xd1 = *(unsigned int *)(BOOTFLASH_ADR); xd2 = ...
Ultra-wideband (UWB pulse) uses a frequency band greater than 3GHz. Compared with the 2.4Ghz (mobile phone, WIFI signal) frequency band, the diffraction performance of UWB signals is very poor, which ...
1 Introduction
The high temperature tester is mainly used for temperature tracking measurement and data acquisition during the heating process. By systematically analyzing the test data, the...[Details]
Do you often have to add brake fluid to your car's brakes? The fact that you need to pump out the brake fluid to make sure there is no gas in the brake fluid line may not be done by the car owner h...[Details]
For a long time, due to the limitation of hardware conditions, the display devices of traditional small handheld devices such as PDA are usually monochrome LCD, and the user interface is very simpl...[Details]
With the rapid development of urban economy, elevators are increasingly used as a vertical transportation tool. However, elevator fault detection and maintenance, especially the role of elevator remot...[Details]
From the PIC16F946 datasheet, we know that there are two ways to write values to the LCD for display:
1. Directly write the value to LCDDATA1~LCDDATA23
2. Use disconnect t...[Details]
LED is the abbreviation of light emitting diode, which is an electric light source made of semiconductor technology. The core part of LED is a chip composed of P-type semiconductor and N-type semi...[Details]
It is well known to automotive suppliers that automakers are demanding more from their supply base. For connector suppliers, this means stricter requirements for product performance, stability and ...[Details]
The era of mobile access to the Internet has arrived, and it will rapidly change the business and infrastructure needs of mobile operators under a whole new trend of requirements. We need 4G LTE to...[Details]
Today, with energy becoming increasingly scarce, the utilization of natural energy has become the focus of people's attention. Among various natural energies, the endless solar energy is highly fav...[Details]
With the rapid development of wireless
digital communication
, more challenges have been raised for integrated circuit design and testing. In the product design stage, in order to ensure
t...[Details]
The launch of Shenzhou IX is imminent, and Tiangong is welcoming visitors again. Yesterday, Professor Fu Qiang, Vice President of the Institute of Science and Industrial Technology of Harbin Instit...[Details]
Abstract: In order to realize wireless automatic alarm and monitoring of major safety places, based on the basic principle of pyroelectric infrared sensing, a detector for receiving infrared radia...[Details]
The principles to be followed are as follows:
(1) In terms of component layout, related components should be placed as close as possible. For example, clock generators, crystal oscillat...[Details]
1 Introduction
Automatic Test
System The ATS (Automatic Test System) integrates all the stimulus and measurement equipment required for testing.
The computer
efficiently comp...[Details]
Abstract: Based on the analysis of the characteristics of the IRIG-B (DC) code type, a design method for IRIG-B (DC) time code decoding is proposed. This method consists of a small number of periph...[Details]
PCB Design
京公网安备 11010802033920号
EEWORLD
